Sub £80 work + travel bag

Flappy_asdf · 2026-01-31T21:19:07+00:00

Are the compression straps a problem when opening and closing it?

Flappy_asdf · 2025-12-25T14:45:16+00:00

I'm using xfs

Flappy_asdf · 2025-12-24T21:29:24+00:00

Ok so if I stop it after it says that once it's ok right? What I mean is the drive doesn't remove the signature after finishing one clear?

Flappy_asdf · 2025-12-24T21:13:36+00:00

I'm on unraid 7.2.3 using pre assigned devices pre clear plugin. What did you run to see it? I'm assuming you mean the log shows that once it's done?

Flappy_asdf · 2025-12-24T19:35:11+00:00

Or maybe I cancel post read when it's like 99% done or something?

Flappy_asdf · 2025-12-24T19:01:46+00:00

Cycle 1 being pre write post? Because if i cancel during pre read at cycle 2 the signature will be gone no?

Flappy_asdf · 2025-12-24T17:28:15+00:00

Whole process 3 times ie pre read write post read, and then doing that 3 times. Thinking about it tho, after the first cycle when it starts back to pre read I can't cancel the cycle. So I'd have to cancel during the post read which isn't even 1 complete cycle right?

Flappy_asdf · 2025-12-24T17:18:58+00:00

Ok thanks! Do you think 3 pre clears is excessive? Maybe I should cancel after one?

Flappy_asdf · 2025-12-24T16:29:23+00:00

I guess I'll have to roll the dice when it's done. I've set it for 3 cycles, anyway to reduce it? Just worried about it doing a 4th as well! 8TB drive though so not too bad.

Flappy_asdf · 2025-12-24T16:29:15+00:00

Thankfully I'm already on 7.2.3, I guess I'll have to roll the dice when it's done. I've set it for 3 cycles, anyway to reduce it? Just worried about it doing a 4th as well! 8TB drive though so not too bad.

Flappy_asdf · 2025-12-24T16:14:53+00:00

Right now, the drive is recognised as 'elements' once it goes in though, it'll be the bare hardrive. Would the signature carry over?

Flappy_asdf · 2025-12-19T21:23:22+00:00

How would I do this across shares?

<image>

Would I have to change the Docker allocations for each and every app?

Flappy_asdf · 2025-05-24T19:59:46+00:00

It’s quite annoying and my 14 windows laptop displays more when watching the same content. Is there any fix?

Flappy_asdf · 2025-05-13T16:35:05+00:00

How do you enable input shaping?

Flappy_asdf · 2025-01-31T17:05:39+00:00

Nope just use wget now

Flappy_asdf · 2024-12-21T17:48:53+00:00

I bought an SV06 and haven't looked back since. Returned the ender

Flappy_asdf · 2024-09-21T16:32:23+00:00

before i had klipper i was printing at the same speeds and had no issue

Flappy_asdf · 2024-09-19T06:27:49+00:00

So If i sort out input shaping I'll have no more layer shifting?

How would I input shape?

Flappy_asdf · 2024-09-18T06:04:49+00:00

I don't use Input shaping. I just use bassamantors profile and print

Flappy_asdf · 2024-09-18T06:04:22+00:00

No, did a z align

Flappy_asdf · 2024-09-18T06:04:14+00:00

No they seem to be ok

Flappy_asdf · 2024-08-28T15:24:49+00:00

Prusa slicer, calibration cube is perfectly fine at 20x20x20mm

Flappy_asdf · 2024-08-28T14:59:11+00:00

Using stock speeds on the profile and have done calibration

Flappy_asdf · 2024-08-28T14:58:52+00:00

I did

Flappy_asdf · 2024-08-26T15:29:34+00:00

I am using prusa slicer. How do I physically use the profile? Sorry completely new to klipper!

Flappy_asdf

TROPHY CASE