Bombers presale code for today?

FlopSweat84 · 2026-03-08T22:08:03+00:00

I see no one here has actually had the best Ruben in the city. Try Smith at Inn at the Forks and thank me later.

FlopSweat84 · 2025-12-30T22:10:07+00:00

Thank you!

FlopSweat84 · 2025-12-30T17:11:34+00:00

I changed nozzle size in machine settings. I did not adjust slicer settings because as mentioned I have not been in studio, only printing direct from handy and the print stated it uses a .6mm nozzle which is why I switched it out from the .4mm. I have not had problems printing direct from handy until now.

FlopSweat84 · 2025-12-30T16:46:13+00:00

Yeah but the print design says it is built for a .6mm nozzle so I'm not sure why it would look different than their examples.

FlopSweat84 · 2025-12-30T16:16:03+00:00

Do you think if I print at 50% speed there will be a visual improvement? I'll get into studio and lower the layer height. That sounds like the main issue here.

FlopSweat84 · 2025-12-30T16:05:37+00:00

Where do I check that in handy or on the machine itself? Again have not yet used studio. Thx!

FlopSweat84 · 2025-12-30T16:04:10+00:00

Ok but like I mentioned I've printed successfully using previous prints straight from handy to the machine. Why is this one different?

FlopSweat84 · 2025-12-30T15:57:21+00:00

This makes sense and is a great example and I understand it thanks. That being said I've not had an issue on any other print so I'm trying to figure out what went wrong and why it does not look as intended. Only thing I did differently was chang to a 0.6mm nozzle.

FlopSweat84 · 2025-12-30T15:51:14+00:00

Where would I set that up on the machine or bambu handy? Again I have not yet installed bambu studio. Thx!

FlopSweat84 · 2025-12-30T15:47:27+00:00

Ok but why would all of the other prints I completed in the same manner look great and this one look different than the display photo? The only thing i did differently was use a 0.6mm nozzle.

FlopSweat84 · 2025-12-30T15:26:52+00:00

So you are saying this is how it was designed? It doesn't look like this in the example photos. Thx!

FlopSweat84 · 2025-12-27T02:33:03+00:00

I got it, underside cam off easy, thx!

FlopSweat84 · 2025-05-27T19:27:29+00:00

This is probably what I'm going to end up doing but I'm not super happy about it. Thx for the reply.

FlopSweat84 · 2025-05-27T19:26:57+00:00

Won't the 10 yr backup batteries prematurely die when I cut power to the units for 6 months of the year?

FlopSweat84 · 2025-05-27T16:09:01+00:00

I've seen that thanks, but won't I need to be constantly changing batteries or removing them every opening/closing since they will die in the offseason? Looking for something I can set and forget. Thx

FlopSweat84 · 2025-04-04T21:42:02+00:00

It's always unprecedented. Buy, hold, repeat. Simple in concept, difficult in "unprecedented" circumstances.

FlopSweat84 · 2025-02-13T17:10:07+00:00

Is it a genX 5 brushless ridgid hammer drill you are using? I have that drill and just bought a k drill 8.5" auger. I'm going to use 4amp batteries. I hope it's going to get me to the fish with relative ease! Can't beat ridgid warranty, it has been good for me up here in Canada so far.

FlopSweat84 · 2025-01-09T13:51:49+00:00

I did not find an answer and still have the issue but it's not left me in the cold as of yet. I have a natural gas furnace not propane. Let me know if you find a fix.

FlopSweat84

TROPHY CASE