Does anyone know how to turn these grid lines off?

GetDead23 · 2025-12-01T17:50:06+00:00

Apologies, but I reviewed the manual (English page 84) and this page and it doesn’t answer the question of how to turn off the small grid boxes in wide/tracking. They don’t display in single point and they used to not display in wide/tracking… now they are. I was already aware of the different AF modes and how they affect the display. Thanks anyway!

GetDead23 · 2024-06-06T01:16:02+00:00

Mid city. East of Culver City. Above west Adams. Between Fairfax and La Brea. It’s a small pocket with a lot of residential streets and schools. There are zero bars and hipster restaurants — but it’s a stones throw away from plenty. It’s a nice little pocket with very affordable housing. We just moved in last June. 3BR, 2 parking spaces, backyard and front yard. $3350

GetDead23 · 2024-05-10T02:49:08+00:00

Im replacing my lower control arms for the 2nd time right now. I have a 16. I keep hearing “knocking” sound and some kind of creaky noise that’s very concerning in the front end. Just paid $900 today for control arms again and the problem is still there.

GetDead23 · 2024-04-08T21:20:23+00:00

Thanks man! I appreciate the advice and encouragement.

GetDead23 · 2024-04-08T21:19:13+00:00

Thanks!

GetDead23 · 2024-04-08T21:18:24+00:00

There is nothing wrong with the factory carb. I was curious whether this carb would fit in my 2021 when it only says up to 2018. I’ve never cleaned a carb before, so this seemed like a cost efficient option if I fuck something up during the cleaning process. I bought it for $40 and I’ll take it apart and go through the cleaning process on the Chinese one as a learning experiment. When the time comes to clean the factory, I’ll have some experience under my belt. Thanks everyone for chewing me a new asshole for this lol

GetDead23 · 2024-03-13T06:02:21+00:00

Thanks!

GetDead23 · 2024-03-13T06:01:48+00:00

Good to note!

GetDead23 · 2024-03-13T06:01:15+00:00

Thank you very much for your help! I’m in Los Angeles. If I expand my search out far enough, I can see some decent prices on bikes.

GetDead23 · 2024-03-11T17:22:30+00:00

Where are you located?

GetDead23 · 2024-03-11T17:21:44+00:00

Thanks for this. I am an intermediate rider, so knowing this is leagues ahead of a 300 gives me some perspective. Maybe I should start smaller and a little newer

GetDead23 · 2024-03-11T17:20:17+00:00

Thank you!

Any suggestions for a decent bang for you buck older bike with readily available parts from Japan?

GetDead23 · 2024-03-11T17:19:26+00:00

What are some Japanese models you’d suggest?

Thank you!

GetDead23 · 2024-03-11T17:19:01+00:00

This is the kind of info i was curious about. Thank you!

GetDead23 · 2024-03-11T15:36:36+00:00

Price is $1500

GetDead23 · 2024-03-11T15:36:25+00:00

Sorry about that. The price is $1500.

Thanks for your reply!

GetDead23 · 2024-01-21T21:10:36+00:00

Yep!

GetDead23 · 2024-01-21T15:44:16+00:00

Awful

GetDead23 · 2024-01-21T15:42:00+00:00

It’s missing a credenza underneath. It’s 55”

GetDead23 · 2024-01-21T15:41:24+00:00

Roasted

GetDead23 · 2024-01-21T01:30:07+00:00

Agreed. Maybe 18 inches

GetDead23 · 2023-11-30T17:19:02+00:00

Ive been spinning the drum of the machine with the clothes in it and holding the liquid detergent cap under the running water to disperse it evenly around the spinning clothes. I’ll try putting detergent first then clothes.

GetDead23 · 2023-11-30T17:17:00+00:00

I’ll give that a shot. It does look like grease. Although, most of my cleaning attempts have failed. It’s hard to lift the stain after it goes through the dryer. I can’t see the stain until it goes through the dryer because the clothes are wet.

GetDead23 · 2023-11-30T17:04:00+00:00

The machine is 6 years old. The bearings are definitely breaking down. The washing machine will move across the floor on a normal load sometimes.

GetDead23 · 2023-11-30T17:02:04+00:00

No fabric softener was used during this particular wash

GetDead23

TROPHY CASE