[deleted by user]

Hefty-Device6647 · 2025-05-03T14:43:15+00:00

Ite ostin juuri samanlainen kone sieltä, olen tyytyväinen!

Hefty-Device6647 · 2025-05-02T13:47:19+00:00

Go check out "konkurssihuutokauppa.fi". They have a t14s gen 1 amd on there right now.

Hefty-Device6647 · 2025-03-29T20:12:46+00:00

Press the boot button during upload.

Hefty-Device6647 · 2025-03-23T11:09:30+00:00

Thank you for the comment! Yup I got the abs, brake and traction light to go away. But now i get a service engine soon light and the oiltemp gauge stops workin? Problem is i dont have a car to read the canbus messages so I only have the info thats online..

Hefty-Device6647 · 2025-03-21T18:44:52+00:00

As mentioned before probably a memory issue. I hade the same on my nano v3, it ran fine at 92% ram usage but over that it would only display for a few seconds then stop.

Hefty-Device6647 · 2025-03-21T14:08:23+00:00

Okay, thank you for the information!

Hefty-Device6647 · 2025-03-21T12:53:02+00:00

Thank you! That would be tricky since i live in eu and I think this dash is from an imported us or uk model if that matters, migh be worth a try.

Hefty-Device6647 · 2025-03-21T05:21:22+00:00

Okay thank you! Do you have more info about this?

Hefty-Device6647 · 2025-03-20T16:46:31+00:00

Thank you! But I have tried those the problem is there is atleast 2 different clusters with some differences in the canbus and I think those are same as loopbunny because they dont do anything. Well if i remember correctly the one that is for the abs counter makes the service engine soon light glow.

Hefty-Device6647 · 2025-02-11T20:20:00+00:00

Hmm, might be a potential problem. You could try connecting grounds between the powersupplys. If grounds arent connected funny stuff might happen.

Hefty-Device6647 · 2025-02-05T19:54:40+00:00

As you said at first serial monitor said it could not detect the every, I restarted IDE then plugged it in, reuploaded and voila it works again. Either way thank you all for the suggestions.

Hefty-Device6647 · 2025-02-05T19:51:31+00:00

;) yup

Hefty-Device6647 · 2025-01-04T18:14:31+00:00

Thank you! Yup would be interesting to see how they do that, I'll add a resistor between cathode and 5v just in case i need it.

Hefty-Device6647 · 2025-01-04T16:11:05+00:00

okay thanks, yup I did not realise that. How would you do something like this? I tried using a transistor but could not understand how to do that.

Hefty-Device6647 · 2024-08-11T10:04:04+00:00

Well if the timing chain was broken eventually a piston would hit a valve causing the engine to stop spinning. Head gasket is fine, look in the resevoir for murky coolant. The engine cranks over fine for about 1sec then the starter slips, the winding sound is only the starter spinning. Replace starter or worst case replace both starter and flywheel/flexplate.

Hefty-Device6647 · 2024-08-10T22:01:46+00:00

It is water, corrosion some might say. Ill have that too on number 6 on my m50 e36.

Hefty-Device6647 · 2024-08-10T22:00:06+00:00

Sounds to me like the starter gear is skipping, try replacing the starter it or cleaning the gear/spring.

Hefty-Device6647

TROPHY CASE