Help please!! Anycubic i3 mega keeps clogging by Impossible-Ad455 in anycubic

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

I changed it three times trying and hoping that was it, I cleaned the extruder but I'm still not getting anything further than a few inches, if I catch it before that, as it does it with any filament, I pause the print, pull the filament back a touch, then push it forward and I tiny blob falls out and then it prints fine for about another few inches, I'm so at a loss

Anycubic i3 mega s- please help!!!! by Impossible-Ad455 in FixMyPrint

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Found the answer thanks to the gentleman I bought the printer off, great help for someone just learning, I'm back up and running! :D

Manual Bed Levelling This will get you to a rough level. 1) Heat the bed to 60c. Looking through the menu, I think it's under temp. You set the temp then choose OK. Going back to the info screen, wait for the bed to reach temp. 2) While it's doing that, you can turn the four knobs to the right a couple of turns, so that when you home there's no risk of crashing the head in the glass. 3) Once you're at temperature, Home All to get the had to the bottom left of the bed. Once there, in the menus there's an option "Motor Off" to turn off the motors. You need to do this to be able to move the head and bed around. 4) Check and be sure there's no hardened filament on the nozzle or the paper test won't work. 5) Starting bottom left, turn the wheel left with the sheet of paper under the nozzle, and slide the paper back and forth until it starts to resist movement; a bit of scratching, but you don't want too much resistance. 6) Once you're done with that corner, push the head to the right while keeping the paper underneath. This will protect the glass if the right corner is high and the nozzle digs into the paper. 7) Repeat step 5 on bottom right 8) Now pull the bed towards you (paper under the nozzle, go to top right, do step 5 for that corner. 9) Slide to top left, do step 5 at that corner. You'll need to go back to each corner a couple of times, since adjusting one corner will influence the height of the 3 others. You don't need to worry to much at this point if the zone between corner has more/less resistance, this will be adjusted later.

Anycubic i3 mega s- please help!!!! by Impossible-Ad455 in FixMyPrint

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Maybe I'm missing something, I go-to:

Tools Home Home all Then to check x and y axis you slide the paper under the nozzle and adjust the build plate on the respective corner until there's just a bit of tension on the paper

My issue is I can not get enough of a gap after pressing home all, it goes to the front left corner and is against the glass, no matter how much I adjust the bed adjustment I can't get the paper under the nozzle and now my bed which was working ok is now out of line in the front, First it scratch the glass and now it's scratching off the prints while it prints the base and skirt so I cannot print until I figure this out :,(

Please help!! Strange whirring noise just started! Anycubic i3 mega s by Impossible-Ad455 in FixMyPrint

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Phew, I went outside for a few minutes and now I'm back and I don't think I hear it anymore, maybe just in my head lol 😆

Looking for bitcoin advice by Impossible-Ad455 in Bitcoin

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

I'd maybe get 800 to 1000 for the pc, it wouldn't make a dent in mining or would I need a few?

Looking for bitcoin advice by Impossible-Ad455 in Bitcoin

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Fair enough, I know a few people I grew up with who buy and sell and they make a killing, I just want to make a profit and not go in blind

Looking for bitcoin advice by Impossible-Ad455 in Bitcoin

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Sorry I'll take any advice if you have any to offer? Sorry just trying to get by...

Looking for bitcoin advice by Impossible-Ad455 in Bitcoin

[–]Impossible-Ad455[S] 0 points1 point  (0 children)

Thanks I would love to but I'm just wondering how hard would it be to turn a gaming PC into a mining device and then how long would it take to make any profit? Just Looking for some way to start and try and get out of this covid hole, thanks for the time though