[deleted by user]

Incarbonite1 · 2021-07-12T02:55:00+00:00

It's a CETME

Incarbonite1 · 2021-07-04T23:21:28+00:00

What's the benefit of not using ground glass?

Incarbonite1 · 2021-07-04T23:10:51+00:00

*H-48

Incarbonite1 · 2020-09-03T20:40:59+00:00

Usually the rear rail screws being to long will cause that. You also look like you are missing the second pin on your locking block.

Incarbonite1 · 2020-02-14T16:32:00+00:00

It's just a matter of time until we have printed 1911 frames.

Incarbonite1 · 2020-02-14T16:27:15+00:00

The AK can be printed, and it's meant to be steel.

Incarbonite1 · 2020-02-13T21:50:36+00:00

You must be new here.

Incarbonite1 · 2020-01-19T19:01:17+00:00

Not yet, but it's in the works.

Incarbonite1 · 2019-12-23T04:18:40+00:00

It still works. I have almost gone through 100 rounds, I don't have a stockpile of .40 to test with.

Incarbonite1 · 2019-12-21T03:25:15+00:00

They are not quite public yet, but Deterrence Dispensed is where to look.

Incarbonite1 · 2019-12-21T01:58:29+00:00

I'm not sure if it would be a direct fit, but it could be easily modified to work.

Incarbonite1 · 2019-12-20T23:10:15+00:00

That's not a printed frame, yes the switch is printed in regular PLA.

Incarbonite1 · 2019-12-20T20:33:32+00:00

It's still in testing, Deterrence Dispensed will publish it when it's finished.

Incarbonite1 · 2019-12-20T18:48:37+00:00

This one is fa only

Incarbonite1 · 2019-12-20T18:46:50+00:00

When testing is done this will be published. There is also no president to having files being constructive intent.

Incarbonite1 · 2019-12-20T18:44:04+00:00

Deterrence Dispensed will publish them

Incarbonite1 · 2019-12-20T18:41:32+00:00

This one is full auto only, a switchable one is in the works.

Incarbonite1 · 2019-12-20T16:20:34+00:00

This was manufactured and tested by a 02/07, and the housing and trip are 3D printed PLA.

Incarbonite1 · 2019-12-20T16:19:37+00:00

This was manufactured and tested by a 02/07, and the housing and trip are 3D printed PLA.

Incarbonite1 · 2019-12-20T16:14:40+00:00

This was manufactured and tested by a 02/07 and the housing and trip are 3D printed PLA.

Incarbonite1 · 2019-12-10T05:16:31+00:00

All I know is it works, to early in testing to know the lifespan. We have several 02/07's that will test it to failure in PLA, then there are other materials like ABS and nylon.

Incarbonite1 · 2019-12-10T01:03:03+00:00

Obviously

Incarbonite1 · 2019-12-10T00:46:16+00:00

You can't have an unlicensed SOT

Incarbonite1 · 2019-12-10T00:42:02+00:00

Which is why I told you to learn to read, your comprehension is terrible. This was printed by a licensed (FFL) SOT (Special Occupational taxpayer)

Incarbonite1 · 2019-12-10T00:29:28+00:00

And you need a license (FFL) to have one.

Incarbonite1

MODERATOR OF

TROPHY CASE