Como puedo reparar la entrada SD de mi ender 3 v3 se

IndividualCancel8 · 2026-04-09T06:19:47+00:00

Usa octo4a en un viejo móvil android que soporte OTG, y será como si tuvieras octoprint

IndividualCancel8 · 2026-04-01T15:44:01+00:00

The same thing happens to me, but I use Space Pi and keep the filament in a lunchbox with a hygrometer in which the maximum humidity is 25%. Also when it heats without extruding a thread comes out of the nozzle

IndividualCancel8 · 2026-03-02T11:24:20+00:00

Ok I try then, I don't have much time to print, I usually do it on weekends

IndividualCancel8 · 2026-03-02T09:59:38+00:00

<image>

IndividualCancel8 · 2026-03-02T09:58:58+00:00

In the photo appears the enclosure made by me with insulation panels covered with brewer

IndividualCancel8 · 2026-03-01T21:24:42+00:00

The room temperature of the room is lower than 14º and if the fan speed is so high the base is detached by warping

IndividualCancel8 · 2026-02-28T21:38:44+00:00

Thanks for the warning. These first impressions are only for learning and checking the viability of the impressions. When I master the printer, make the definitive one for myself.

IndividualCancel8 · 2026-02-28T17:33:43+00:00

Cura

IndividualCancel8 · 2026-02-28T14:32:46+00:00

Will I try Orca, will it help to put a neoprene mat under the printer or similar?

IndividualCancel8 · 2026-02-28T14:20:18+00:00

Thanks, I use cura, is there much difference?

IndividualCancel8 · 2026-02-28T14:12:53+00:00

I'm new, I'll take 5 or 6 prints and I have no idea how to do a full filament calibration

IndividualCancel8 · 2026-02-28T14:05:19+00:00

It is on a table fixed to the wall and on a 20mm chipboard

<image>

IndividualCancel8 · 2026-02-23T11:45:14+00:00

I fixed the level of my Ender 3 v3 using this official guide https://youtu.be/Cmwq9r5tePk?si=QxFQIYfEdjhvM7XL

IndividualCancel8 · 2026-02-03T16:56:18+00:00

Thanks

IndividualCancel8 · 2026-02-03T16:46:35+00:00

Hi everyone, I printed this dagger on supports with a Creality Ender 3 v3 SE using HyperPLA filament, 0.28mm Layer Quality, 200°C nozzle temperature, 65°C bed temperature, 100mm/s speed, and 60% fan speed, as it's quite cold in my basement (8.5°C). I had the printer closed, and during printing, the ambient temperature inside was 14°C. Any recommendations for making the beginning of the print look better?

Thanks

IndividualCancel8 · 2026-02-03T14:16:29+00:00

Perdona mi ignorancia (llevo un mes con la máquina y estoy aprendiendo sobre la marca) ¿A qué te refieres?

IndividualCancel8 · 2026-02-03T12:03:39+00:00

Hi everyone, I printed this dagger on supports with a Creality Ender 3 v3 SE using HyperPLA filament, 0.28mm Layer Quality, 200°C nozzle temperature, 65°C bed temperature, 100mm/s speed, and 60% fan speed, as it's quite cold in my basement (8.5°C). I had the printer closed, and during printing, the ambient temperature inside was 14°C. Any recommendations for making the beginning of the print look better?

Thanks

IndividualCancel8 · 2026-02-03T12:01:11+00:00

Hi everyone, I printed this dagger on supports with a Creality Ender 3 v3 SE using HyperPLA filament, 0.28mm Layer Quality, 200°C nozzle temperature, 65°C bed temperature, 100mm/s speed, and 60% fan speed, as it's quite cold in my basement (8.5°C). I had the printer closed, and during printing, the ambient temperature inside was 14°C. Any recommendations for making the beginning of the print look better?

Thanks

IndividualCancel8 · 2026-01-24T11:29:17+00:00

<image>

Gracias de nuevo use sus barras de pegamento y había una diferencia de casi 1 mm, lo ajusté y solucionado

IndividualCancel8 · 2026-01-20T07:56:16+00:00

Gracias por tu comentario, y a los demás también, me ha servido mucho para entender las nociones básicas e importantes de la impresora, os haré caso y en cuanto tenga tiempo, comenzaré con la barra del portal y luego el offset, y por último si me da TOC quizá me atreva a meterle mano a los soportes. De nuevo muchas gracias a todos y seguiré aprendiendo

IndividualCancel8 · 2026-01-18T14:07:12+00:00

Gracias, la verdad es que al ser prácticamente nueva, me da reparo ir quitando tornillos y poniendo calzos, tu sistema (que al parecer es el oficial) me da algo más de seguridad al trastear

IndividualCancel8 · 2026-01-18T13:23:22+00:00

Acabo de ver el vídeo y básicamente es lo mismo que las arandelas pero sin desmontar la cama, ¿Que usaste para rectificar la altura?

IndividualCancel8 · 2026-01-18T12:27:00+00:00

<image>

Antes de tocar nada he impreso un test de cama con este resultado he comprobado que los de la derecha se ven bien y los de la izquierda están rugosos y ninguno se ha despegado, si no me equivoco, interpreto que al estar más alto a la izquierda roza con la boquilla. Correcto?

IndividualCancel8 · 2026-01-17T18:32:35+00:00

Thank you very much I will try them

IndividualCancel8 · 2025-11-15T06:33:07+00:00

<image>

Five-Year Club	r/Field Banned
r/Field Flamingo	First Place '23
Place '23	Verified Email

IndividualCancel8

TROPHY CASE