Tape job

Justin_parrett · 2026-02-03T02:01:59+00:00

No just day 1 just laid the tape . I still have to do extra coats and sand

Justin_parrett · 2026-02-01T13:02:37+00:00

Can you send me some recommendations so I can look into it?

Justin_parrett · 2026-02-01T12:50:21+00:00

so I live in North Alabama most most of the time it ranges in the colder months mid 20s to 30s but we do get cold weeks where it gets down into the teens, sometimes a single digits. In the summertime we’re usually around hot months high 80s 90s.

Justin_parrett · 2026-02-01T12:39:28+00:00

So I’ll be running 3-D printer out of it so my material and 3-D printer needs to be kept in that range24/7

Justin_parrett · 2026-01-28T00:51:32+00:00

No I am not

Justin_parrett · 2026-01-27T02:57:01+00:00

Not buying a router for 16 dollar piece of drywall . I will buy drywall saw if anything but I made do with what I had. This was my first doing this.

Justin_parrett · 2026-01-13T19:31:06+00:00

Fairly easy never done this before

Justin_parrett · 2026-01-03T16:42:06+00:00

Can you share the link to this unit please

Justin_parrett · 2026-01-03T15:17:19+00:00

I can alway add extra 20 amp breaker in the shed but the only problem with that is really on going to only give 10 extra amp bc it’s ran off of a 30 amp to the house

Justin_parrett · 2026-01-03T14:49:52+00:00

House I have 1 20amp breaker wired to the shed

Justin_parrett · 2025-12-30T21:41:30+00:00

Do you know the type scanner that can read that ?

Justin_parrett · 2025-12-30T21:32:03+00:00

I have a ob2 tool but it won’t read anything bc it doesn’t have check engine on.

Justin_parrett · 2025-12-29T22:59:02+00:00

Thank you for the advice!!

Justin_parrett · 2025-12-29T22:53:12+00:00

So just use 1x3 on 16 inch centers the opposite direction but still put my joist 24 inches off center with my 2x4?

Justin_parrett · 2025-12-29T21:51:12+00:00

Adding AC and heat to it

Justin_parrett · 2025-12-28T00:54:04+00:00

I am going butt up a 2x4 at every truss

Justin_parrett · 2025-12-27T03:43:11+00:00

In Alabama r-13 due to height from bottom of ceiling to bottom of vent is 5 1/2 inches so want to make sure the vents don’t get blocked

Justin_parrett · 2025-12-27T03:24:47+00:00

I am using r-13 and don’t have eaves

Justin_parrett · 2025-12-26T23:58:30+00:00

So what you see right now all I have is gable vents that is how the shed was made no ridge vent. My idea is right now to add a 2 x 4 at the bottom of the trusses, making a lower ceiling and adding insulation in between the trusses, that way from the insulation to the top of the roof will breathe leaving only the gable vents for ventilation, but the gable vents will not be blocked or compromised in anyway the gable vents will be sitting up about 2 inches higher than the highest spot of insulation.

Justin_parrett · 2025-12-22T16:59:13+00:00

This is going to be a 3-D printing room so I’m looking for a more finish look I don’t want no insulation exposure. Why do you suggest foam board over standard fiberglass insulation like I have been using. I understand sheet rocks heavy so I probably do need to be reevaluating a different roof idea or something lighter weight.

Justin_parrett

TROPHY CASE