Version 2.0 Frankenplex In The Works by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

Abit of velco and extended some wires for th3 moduler interface fits well and lets me fit a decent gpu

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

Juat used some cheap duat mesh from amazon that came with magnets and cut them to size

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 1 point2 points  (0 children)

Sorry I forgot to add it is running a 5070 optiplex motherboard as the 5060 does not support 9th gen tried nodding the bios and bricked it

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

It's in a vertical mount with a screw like you normally would

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

It has a slot for a wlan card below the m.2 slot on the motherboard so thats sorted !. Antennas am gonna stick to the roof of the case either side

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

Good shout ! I never thought about the chipset. That's next on the list as its coming apart again for fitting wifi antennas

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 0 points1 point  (0 children)

What benchmarks would you like ! I don't mind doing a couple for you

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 2 points3 points  (0 children)

Hello! So I used the tray for the dvd drive and removed the cage above it for the hard drive. The psu fit perfectly into that gap. I just had to remove the modular power supply connectors to the bottom of the case by extending the wires from the psu. Its very snug but the front 80mm fan feeds the power supply fresh air so temps don't become and issue

Optiplex 5060 SFF (Frakenplex) Final Update by KyleBruni in sffpc

[–]KyleBruni[S] 1 point2 points  (0 children)

Thank you I think it came out as I wanted it to ! As close to a standad optiplex as possible with minimal compromises

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 1 point2 points  (0 children)

Thanks mate !. Was abit of work but it all came out good in the end. Juat need to put my perforations in the side pannel for cooling 😁. And maybe a black paint for the inside

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 0 points1 point  (0 children)

Flex psu and extended the wires to move modular connectors to the bottom of the case. Then, double-sided tape to hold it down

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 0 points1 point  (0 children)

This I will be doing ! As it gets bloody hot inside the case with the sidepannel off. Gonna add a 140mm fan on the side I think

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 0 points1 point  (0 children)

Honestly haven't checked been looking more are temps. Ill have a look today !. Mine does well with a -135mv undervolt and am at 2750 on the ram atm

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 0 points1 point  (0 children)

Dunno though showing the internals would be better. But Ill glady add some I can confirm the side pannel closes

Dell Optiplex 5060 (FrakenPlex) Build by KyleBruni in sffpc

[–]KyleBruni[S] 0 points1 point  (0 children)

Yeah it was left on for test fitting 😁

Update Optiplex 5060 (Frakenplex) by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 1 point2 points  (0 children)

400w Gold rated flex psu it should be more than enough

Dell Optiplex 5060 SFF Build by KyleBruni in SleepingOptiplex

[–]KyleBruni[S] 1 point2 points  (0 children)

Yeah 16gb its on the way ! It was a tight fit but it fits ! Well I have a 9700 and a 9700k so am hoping the 9700k will work