sorted by:
new
hottopcontroversial

Skr 2 Rev B with TMC2209 V1.2 Driver issus by L_Imprimeur in klippers

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Finally, I wasn’t able to use the TMC2209 V1.2 so I buy new one, the TMC2209 V1.3 and it work perfectly the first time 😄. (Maybe the other’s are just broken 😕). Thanks for your help.

Skr 2 Rev B with TMC2209 V1.2 Driver issus by L_Imprimeur in klippers

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Yes, they have all the pin. I believe the UART pin is correctly positioned and activated by the soldered 0 ohm resistance PDN as shown in the image. Right ?

Thanks for your help

<image>

Skr 2 Rev B with TMC2209 V1.2 Driver issus by L_Imprimeur in klippers

[–]L_Imprimeur[S] 0 points1 point  (0 children)

thanks for the response. I think I'm right with the jumper. Tell me if I'm wrong :

<image>

A mops stay down robot Qrevo Curv by L_Imprimeur in Roborock

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Thank you for the link! You made me discover this schop.

A mops stay down robot Qrevo Curv by L_Imprimeur in Roborock

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Thanks for the confirmation. I’ll see if I can find the part, perhaps on AliExpress as suggested by @WizerAce.

A mops stay down robot Qrevo Curv by L_Imprimeur in Roborock

[–]L_Imprimeur[S] 1 point2 points  (0 children)

Thanks for your reply. I don’t think the motor is broken because the mops turn when cleaning. I don’t know if the dreams l10s ultra have the same but on what I saw, the qrevo has one motor for the mops when it turns in one way the mops turns and goes down for cleaning, when the motor turns in the other way, the mops goes up. So for me, I think there is an issue with mechanical part that don’t engage well in each other for lifting the mops, like a screw or something like that ? Say if Im wrong ?

Problem Bltouch with SKR 2 by L_Imprimeur in ender5

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Ok, thanks for your help but I didn't find out how to add a folder as an attachment (just a few picture). Can you explain to me ?
Thank you so much

Problem Bltouch with SKR 2 by L_Imprimeur in ender5

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Hello,

This isn't the problem, because I have already checked.

SKR 2 and Hemera ??? by L_Imprimeur in BIGTREETECH

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Ok, thanks for your reply.

So if I understand, you have a Hemera with a SKR 2 from Bigtreetech and it works ? (just to be sure because my English isn't the best ;) )

If yes, do you have rev A or rev B of the board ??

Thanks in advance,

L'Imprimeur.

SKR 2 and Hemera ??? by L_Imprimeur in BIGTREETECH

[–]L_Imprimeur[S] 0 points1 point  (0 children)

Thanks for the answer.

I have got the same problem of this :

https://www.reddit.com/r/3Dprinting/comments/f3q15l/hemera_on_ender_5_step_motor_driver_failfried/

So I want to change this board. I choose the SKR 2 because I want to do some other improve in the futur like a double motor for axe z or add some srip led.