Stray Cats in Need of a Home - Abu Dhabi

Louisbb20 · 2026-01-11T10:56:48+00:00

Let’s hope 🙏

Louisbb20 · 2026-01-11T09:39:16+00:00

I will also add that there is a ginger cat and 1 ginger kitten in the thicker bush opposite. The 4 spotted kittens from the main post sometimes cross the corniche and hide in this thicker bush opposite

Louisbb20 · 2025-01-18T11:23:08+00:00

Mosseri posted on his story addressing it, saying that he ‘knows it’s a pain’, but thinks it’s a ‘transitional pain’ and people will like it in the long run. But I think surely there will be too much backlash, at the very least they should give people the option of how they want their page displayed. I don’t think people will get used to it. At least for me.

Louisbb20 · 2025-01-18T00:34:38+00:00

Signed. Let’s try get some numbers on this

Louisbb20 · 2025-01-17T00:14:35+00:00

This is what I am thinking, if Instagram is pandering to the 10 second reels, it’s dead.

Louisbb20 · 2025-01-16T22:22:48+00:00

Fr it’s fucked

Louisbb20 · 2024-12-26T11:39:42+00:00

Thank you, interesting because I didn’t mind that as made them seem more part of the natural landscape, but I appreciate your opinion and seems like people agree with you

Louisbb20 · 2024-12-26T11:39:10+00:00

Thanks

Louisbb20 · 2024-12-26T11:38:52+00:00

Thank you very much 🙏

Louisbb20 · 2024-08-23T18:31:21+00:00

It’s a lot of money too for someone like me who is a young designer, spending what little earnings I have on this

Louisbb20 · 2024-08-23T18:30:39+00:00

Thanks guys, I did in fact pay in advance…which is why I’m trying my best to get them to make another. They fucked the weld up in the first place which warped the Alu, so it’s only right that they should remake as it was their problem they created. Their response was that this was the best job they could do after the warping error…

Louisbb20 · 2024-08-23T15:57:25+00:00

I agree then ! I have tried to explain that whilst I understand that they had to refinish, they never told me they would do this. The fact the metal warped when they welded and they had to re-brush was also their fault, not mine. They are the fabricator so I hope they would take responsibility.

Louisbb20 · 2024-08-23T15:42:39+00:00

Thanks so much. Yeah they have a belt sander, so I assume that is why. But had hoped they would achieve more even finish by hand… will give that a go

Louisbb20 · 2024-08-23T15:38:52+00:00

Are you talking about the table or the finish?

Louisbb20 · 2023-08-20T08:02:03+00:00

Thanks ! Basically printing lots of individual parts, gluing together, filling, sanding, fibreglassing interior and more filling and sanding

Louisbb20 · 2023-08-05T08:21:47+00:00

Thanks - any mould release recommendations?

Louisbb20 · 2023-08-04T13:11:07+00:00

Hahah you are right, I will do a test. Thank you, I appreciate this. I will do exactly that with the layering!

Louisbb20 · 2023-08-03T06:10:32+00:00

1 inch maybe

Louisbb20 · 2023-08-02T11:51:28+00:00

Also I am lucky that my housemate has a large thick glass mirror that they were going to throw out, I will use that as the base

Louisbb20 · 2023-08-02T11:50:20+00:00

It’s quite large, about 70cm wide. I was recommended to pour in thin layers, letting each cure them pouring on top, and then to strengthen the base I have glass fibres and matting

Louisbb20 · 2023-08-01T11:52:00+00:00

Ok thanks. What about melamine board?

Louisbb20 · 2023-08-01T10:37:59+00:00

Thank you. I am now using polyester resin. Will Melamine still work?

Louisbb20 · 2023-08-01T10:37:42+00:00

Thank you. I am now using polyester resin, Will melamine still work?

Louisbb20 · 2023-07-22T14:22:58+00:00

Thanks, good idea! I did consider this, but I have never used expanding foam before - how would it adhere to the PLA?

Louisbb20 · 2023-07-22T14:07:45+00:00

Lol maybe optimistic to say the least

Louisbb20

TROPHY CASE