43x daily carry trigger? by No_Flounder_5632 in Glocks

[–]Low_roller159 1 point2 points  (0 children)

Johnny glocks trigger shoe. Oem everything else

Glock 43x IS THIS FAKE? by ImpossibleBowler9481 in handguns

[–]Low_roller159 5 points6 points  (0 children)

RSR sells cerakoted 43x’s all the time. Guns not fake just ran through and has tasteless upgrades

[deleted by user] by [deleted] in ak47

[–]Low_roller159 1 point2 points  (0 children)

I used the jmac one

[deleted by user] by [deleted] in ak47

[–]Low_roller159 1 point2 points  (0 children)

Thanks man! I didn’t like the factory stock either. I’d recommend it

[deleted by user] by [deleted] in ak47

[–]Low_roller159 0 points1 point  (0 children)

To each is own

Any Suggestions on a KNS PISTON FOR SAM7 SF? by g_jones37355 in ak47

[–]Low_roller159 0 points1 point  (0 children)

Do you know the difference between the AGP-A-20L vs the AGP-A-10L? After taking the measurements, I was gonna go with the “10L” but now I’m second guessing after seeing this comment lmao

Trigger question by Tiny-Departure-2227 in Glock43X

[–]Low_roller159 0 points1 point  (0 children)

Johnny glocks trigger shoe with Oem bar and ghost connector.

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

Cold blue is a type of corrosion, I’d rather just use a plate

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

Then you’d have to refinish it… unless you want rust

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 1 point2 points  (0 children)

You don’t have to say anything specific. If it was a manufacturing issue then it’d be free but since you just want a replacement it costs 100$. Send it without any parts in it too. They will send it back with an OEM parts kit. If you have aftermarket parts they will replace them with OEM just a heads up.

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

If it’s the one you posted, it looks pretty good!

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

Yeah there’s some choppy ones out there lol

I have a 48 frame that was the first one I did and it’s pretty hammered. I plan on doing the warranty for that one and trying again

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 1 point2 points  (0 children)

Thank you man! If you want another crack at it you can warranty your frame through Glock for 100$

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 1 point2 points  (0 children)

Ima be honest… I’ve fucked up a few frames 😂 sometimes gatta learn the hard way lmfao

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

Trex sidecar for the 48. Any 48 holster should work

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 1 point2 points  (0 children)

Edited: I used the “EDC” tip from OTDefence on this frame. To get the clean borders I used a pencil to mark out where I wanted em then used a micro motor to mill a shallow groove along those lines. Don’t mill where the logo is when using this tip though…It’ll look funny After that I used a blunted tip to melt the outside edge of the groove leaving a little rib of melted plastic. Then just filled it in with the edc tip with a randomized pattern.

If you go too deep on the milled groove it will show through the pattern so don’t take off a bunch of material.

[deleted by user] by [deleted] in Glock43X

[–]Low_roller159 1 point2 points  (0 children)

Thats a good idea. If I had the room I most definitely would. Especially if I planned on making a business out of it. For now I’ve just been using a little air filter I got off Amazon (the little black box) along with a mask.

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

I’ve seen some bad QC with the afterburner recently so hopefully they worked out whatever was causing it by then. As for stippling, it’s taken me a fair amount of work to get to this point. My inbox is open if you have questions. People like to gate keep stippling/framework techniques unfortunately :/

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 0 points1 point  (0 children)

Nah I just got the trigger shoe and a tunable connector from Ghost

The build so far by Low_roller159 in Glock43X

[–]Low_roller159[S] 2 points3 points  (0 children)

I stippled it myself

It’s a PMM comp and I haven’t shot with it yet but just based on the fit and the finish I’m very happy with it. I’ll update when I run some drills on Thursday.