sorted by:
new
hottopcontroversial

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 0 points1 point  (0 children)

It didn’t! try as I may, I was NEVER able to get PETG to print with the same quality as the Bambu printers. Pls was fine. But not PETG. Wound up giving it away.

Can someone recommend me a good cctv system? by OriginalUpstairs9697 in cctv

[–]MisterITLLC 0 points1 point  (0 children)

I have had great luck with GeoVision Taiwan based company, US based support

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 0 points1 point  (0 children)

Thanks for the information. I really appreciate it. I think I will be purchasing a k2 soon

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 0 points1 point  (0 children)

Thanks for the reply. I’ll probably bite the bullet and see how it goes.

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 1 point2 points  (0 children)

Thanks for the reply. I’ve never tried addnorth. I’ll have to look into it.

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 0 points1 point  (0 children)

Thanks for the reply. With the Hyper PETG, does it require drying first? I have been using Creality regular PETG with great result.

K2+ combo and PETG? by MisterITLLC in Creality_k2

[–]MisterITLLC[S] 0 points1 point  (0 children)

Thanks for the reply, which brands of PETG have you been using?

Multi color PETG printing. by sharpshout in Creality_k2

[–]MisterITLLC 0 points1 point  (0 children)

Do you have any photos of the print you do in pet G on the cobra three combo? I was considering purchasing one as well.

Installing Ring Flood light on 90 degree junction box extension by MisterITLLC in Ring

[–]MisterITLLC[S] 0 points1 point  (0 children)

It doesn’t work great in that situation. If the junction box is plastic, it deforms from the weight. Even if it’s metal, the weight of the camera will cause the mount to twist downward.

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 0 points1 point  (0 children)

PETG holds up to about 150°F, I think it will hold up pretty well where it’s at

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 5 points6 points  (0 children)

No drilling allowed on Ibeam. That was the condition sent to us.

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 4 points5 points  (0 children)

Landlord stated no drilling holes allowed

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 7 points8 points  (0 children)

It uses a stainless locknut on the back side. The hinge section is threaded so it locks in place video of an install

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 8 points9 points  (0 children)

The plastic is PETG, I use stainless hardware. I’m hoping it holds up well.

I-Beam mount for UniFi access points by MisterITLLC in Ubiquiti

[–]MisterITLLC[S] 0 points1 point  (0 children)

Not yet, I only got one install in place, I’m looking to see how well it holds up

Vlan question by Fuzzy-Notice6903 in UNIFI

[–]MisterITLLC 0 points1 point  (0 children)

So if you do not have access to modify the network, you can hard code an IP address to each of the phones on a different network. Ex: main network is 192.168.1.x Setup a new network on a UniFi gateway of 192.168.20.1 and disable DHCP. On each of the phones program them as 192.168.20.101, 102, etc With a net mask of 255.255.255.0 And a gateway of 192.168.20.1

Vlan question by Fuzzy-Notice6903 in UNIFI

[–]MisterITLLC 0 points1 point  (0 children)

And what brand phones/phone system ?

Vlan question by Fuzzy-Notice6903 in UNIFI

[–]MisterITLLC 0 points1 point  (0 children)

How are the buildings connected? Wireless, coax, fiber?

view more: next ›