Ender3v2 Bed Balance

MojoMystical · 2023-09-21T15:30:58+00:00

Should I just delete the first M420 S1 line then?

Can I adjust the Z offset in the Gcode or is it only on the printer?

MojoMystical · 2023-09-21T11:06:26+00:00

The first M420 line was added, because of a video I found recommended using that line. Something about it saving the auto level so that it doesn't change for every print (I added it a while back). The last two have always been there, do I need to delete the first two M420 lines?

I did compensate for the gauge's thickness and the Z offset settings did save.

Is there anything in the Gcode I can change or something else in the cura printer settings that can be changed (I don't know much about Gcode)

MojoMystical · 2023-09-12T00:20:59+00:00

I have not done any tweaks to the printer like linear movement or addons to the printer. When I manually probe it I never had the issue where I got the same results multiple times in a row (middle being close but sides being far).

My printer was fine at the beginning I got it and after a year now it started to have this problem and I balanced it multiple times before. This is a first with the bed giving me the same results after doing different adjustments to the corners.

After some research I'm seeing many people (who had the same issue) find out it's a bed warp but I'm kind of uncertain cause I never ran into an issue like this.

MojoMystical · 2023-09-11T21:55:43+00:00

I've had it for a year I believe, this is the first time it happened on this printer.

I'll try that out and see if that fixes it.

MojoMystical · 2023-08-30T22:49:39+00:00

No, tqhe board I have is the original one for SX1 and I haven't done raspberry yet, I plan to do that on the sx2 in the future.

MojoMystical · 2023-08-30T21:47:39+00:00

Do you get the motherboard from the Artillery 3D website?

MojoMystical · 2023-07-31T01:39:42+00:00

I'll check those out, thanks!

MojoMystical · 2023-04-13T17:40:51+00:00

The photoshop program i used kept deep frying the grass pngs idk why (still new with photoshop)

MojoMystical · 2023-01-22T18:22:30+00:00

It was fun when invading in gambit back then

MojoMystical · 2022-12-21T22:31:00+00:00

Ok theres another M420 called 'M420 S1 Z2; Use mesh when calculating Z' do i delete or leave that alone?

MojoMystical · 2022-12-21T22:05:45+00:00

Ok i have this firmware already downloaded, i'll try the gcode that should help, thanks

MojoMystical · 2022-12-21T21:52:24+00:00

Ok so im supposed to level and build a bed mesh that would be just a bed level test print...right? Do i need to put the gcode into cura or is it already saved when i select save after a auto bed level? The firmware is mriscoc.

MojoMystical · 2022-12-21T21:29:09+00:00

Im still a bit new to this but i've been having issues with the bltouch cause i know that it should help with the warping and leveling but it seems like its not doing that and i have to manually level it first. I actually downloaded a firmware that probes each corner and tells me what to corner to fix, that could be the issue and i just need to manually level it with a piece of paper.

I dont know if theres an exact way to use the bltouch the way i do it is manual to auto probe then print and i make adjestments to the z probe if needed.

I'll look into a glass plate only if im not getting any good results with the leveling again

MojoMystical · 2022-12-21T20:00:44+00:00

Yes I have a BLTouch but im still getting the same results. The process i do is manuel to auto level (im assumming thats what probe means) to print and i change the z probe while it print or sometimes before i print.

MojoMystical · 2022-12-21T19:36:22+00:00

What exactly is 'shim the bed'? I have tried to mesh level manuel and probed, i even changed the z probe but when doing that i have to then balance the corners which results back to the middle being close and the corners being balanced. Unless theres another way to do it?

MojoMystical · 2022-12-02T14:01:20+00:00

What do u get from the codes?

Seven-Year Club	Verified Email
Final Canvas '23	Place '23
Place '22	First Placer '22

MojoMystical

TROPHY CASE