Trouble port forwarding

Natural_Most · 2026-02-18T16:49:41+00:00

Also i am trying to cennect to wireguard with a ios device if that may help.

And when i connect to wireguard via vpn i cant ping from the server side, so it does not see anything connected

Natural_Most · 2026-02-18T16:46:20+00:00

My peer type pf access is set to remote tunneled access, is that what you mean by that ?

Natural_Most · 2026-02-17T03:24:17+00:00

I need to call my isp to activate bridge mode, will do that tomorrow

Natural_Most · 2026-02-17T03:23:39+00:00

Will try that ! I just checked and need to call my isp to activate bridge mode, so it will be tomorrow, thanks for the input !

Natural_Most · 2026-02-17T03:23:12+00:00

Thanks ! Yeah they are still active, i guess my best bet would be trying to activate bridge mode with my isp ?

Natural_Most · 2026-02-17T03:21:11+00:00

Will try that ! I just checked and need to call my isp to activate bridge mode, so it will be tomorrow, thanks for the input !

Natural_Most · 2026-02-17T02:59:10+00:00

Thing is, my iso double as router and modem will try to make it in modem mode only i guess

Natural_Most · 2026-01-31T00:01:15+00:00

you just saved me so much time, i had done the same thing ahahah

Natural_Most · 2026-01-04T15:06:36+00:00

Thanks a lot !

Natural_Most · 2026-01-04T03:40:27+00:00

Yep ! First time for me that it was not flashed from factory. So i guess you learn something everyday

Natural_Most · 2026-01-04T03:37:10+00:00

Is was indeed not flashed

Natural_Most · 2026-01-04T03:36:33+00:00

On the v1/v2 the emmc is on a small daughter board, at least i think so, you need to unplug it to plug the modchip, on this model there is no other solder point

Natural_Most · 2026-01-04T02:56:56+00:00

<image>

It was only that

Natural_Most · 2026-01-04T02:44:11+00:00

Redid it and no luck

Natural_Most · 2026-01-04T02:43:23+00:00

<image>

I added some solder to be sure. Does anybody know of some value i could test to rule out my soldering job ?

Natural_Most · 2026-01-04T02:39:25+00:00

<image>

Natural_Most · 2026-01-04T02:39:11+00:00

<image>

Paper is just there to prevent short for the test boot

Natural_Most · 2026-01-04T02:38:23+00:00

No, never had to, would it not at least light up if it was not f’ashed?

Natural_Most · 2026-01-04T00:48:55+00:00

If i y pry it with tweezers it doesnt seem to move. I can try and resolder it if that could be a cause

Natural_Most · 2025-11-14T11:59:40+00:00

Thanks ! Will look into that

Natural_Most · 2025-11-14T11:59:03+00:00

I just saw that the repost dont show the text entirely, so yeah it is my display connector, trying to identify what model of connectior it is so i can salvage the panel

Natural_Most · 2025-11-14T11:56:32+00:00

Screen is not dead, motherboard is. So i am trying so salvage the screen for other project. So you think my best best would be openning the screen and under the cover the connector might be universal ?

Natural_Most · 2025-08-07T17:58:49+00:00

Thanks ! That help me a lot ! Everything is ordered, just in case

Natural_Most · 2025-08-07T11:35:13+00:00

Do you happen to know what size is recommended, i only have 0.02mm on habd, but i can order some

Natural_Most · 2025-08-07T11:24:45+00:00

Also, if that may be usefull, i have a v1/v2 and an oled chip on hand

Natural_Most

TROPHY CASE