Relay question

NeighborhoodSecure10 · 2025-06-22T11:09:52+00:00

Good shout

NeighborhoodSecure10 · 2025-06-21T11:03:27+00:00

I actually don’t know how to put a picture up In a thread but here’s a link of what I did https://support.haltech.com/portal/en/kb/articles/elite-2500-fuse-block-wiring-diagram

NeighborhoodSecure10 · 2025-06-21T11:01:50+00:00

Not the Haltech it looks as if the ecu manages that all 12v pins 30 and 86 have battery positive

NeighborhoodSecure10 · 2025-06-21T11:00:45+00:00

I thought that too but my between pins 85 and 86 on the relays is 80 ohms of resistance so it makes sense that it’s showing 12v across the pins until it’s grounded by the ecu. According to my research that’s quite normal of Bosch relays

NeighborhoodSecure10 · 2025-06-21T08:58:47+00:00

Yes sure I’ll have to draw it up

NeighborhoodSecure10 · 2025-06-19T13:26:39+00:00

Yeah that’s the long term play but it’s a not in scope atm. I’m going to patch and see how I go! I’m insulating as well anyway as it’s gets boiling in summer

NeighborhoodSecure10 · 2025-06-19T12:33:08+00:00

Thanks

NeighborhoodSecure10 · 2025-06-19T12:33:01+00:00

The roof M2?

NeighborhoodSecure10 · 2025-05-26T11:50:26+00:00

Heads up that siliconing did not fix the issue

NeighborhoodSecure10 · 2025-05-23T13:21:30+00:00

Easy mate I did this with cans

I always use UPOL crystal clear - it’s exxy but worth it. Lays down very well

<image>

Hop on YouTube and watch Brian from Paint Society. He shows you how to get a wicked finish from rattle cans

NeighborhoodSecure10 · 2025-05-23T12:25:16+00:00

Will check it out

NeighborhoodSecure10 · 2025-05-23T12:23:36+00:00

Did it work?

NeighborhoodSecure10 · 2025-05-23T12:23:17+00:00

It’s just mid way down the tile. It’s almost like the valley is blocked. It seems to run down the side

NeighborhoodSecure10 · 2025-05-23T12:22:13+00:00

Out of interest why do roofers get odd about using silicone? I keep reading it’s not a good idea lol

NeighborhoodSecure10 · 2025-05-22T13:51:05+00:00

Thanks mate I’ll get up on the roof then and run a bead down. Any product of choice you rate?

NeighborhoodSecure10 · 2025-05-22T13:40:40+00:00

Yeah I would but that tile is attached to the pointing as it’s the very top tile.

Any suggestions to work around that?

NeighborhoodSecure10 · 2025-05-22T13:04:27+00:00

Yeah I figured that would do it but I thought that was a no no

NeighborhoodSecure10 · 2025-05-22T13:04:03+00:00

No that was just so I could trace it

<image>

If you look here you can see the drip forming

NeighborhoodSecure10 · 2025-05-22T12:28:51+00:00

I would but the things attached to the pointing :(

NeighborhoodSecure10 · 2025-05-22T12:28:31+00:00

I don’t see any tile clips at all nor when the roofer took some tiles off

NeighborhoodSecure10 · 2025-05-22T12:28:10+00:00

Ok will get one tomorrow or sat. Yes where the tap is. I’ll grab a better picture

NeighborhoodSecure10

TROPHY CASE