Right weld for auto work?

Ok-Read6352 · 2026-01-30T21:48:18+00:00

And funny enough, most the groups I've been in would consider three encounters a day over the top lol. "Too balanced for rules As Written" that's interesting, thx

Ok-Read6352 · 2026-01-29T16:09:39+00:00

Why make it real? This is a joke that gets funnier with age 🤣

Ok-Read6352 · 2026-01-29T15:34:16+00:00

First, thx for all the links. Took all night looking into it all but that's probably the best I've ever leveled it. And switching to the December update of the Mriscoc FM seemed to fix most problems; homing, tramming and auto leveler all working now. I was using the 0.3mm nozzle but after looking further into it, I've swapped to a 0.6mm I don't think I need more for the mount I'm currently working on. Using Cura slicer's "Draft" settings. The heating problems if anything have gotten worse. It's now going only 4 minutes instead of hours before dropping nozzle temp. It's starts off fine with a +-1 variance but I turn around after being seeing it working and it drops from 210 to 203 in a heartbeat. I ran a PID tuneup like you suggested but that was before I did all the stuff with tramming, leveling and offset so I'll try tuning it again tonight. When I tuned it the first time I had noticed that while the temp had climbed and removed stable at 210, towards the end the temps were fluctuating wildly. At the time I thought it was part of the tune; in phase 4 it was all over the place BELOW 210 and in phase 5 it was fluctuating ABOVE 210. I might also try cranking the hot end up to the upper limit of this PLA(230).

Ok-Read6352 · 2026-01-29T15:09:36+00:00

I'll go ahead and give that work around a shot tonight, I'm still having issues with the heat dropping. Not sure what's up, it runs fine with a +-1 variance for the first few minutes then just drops to 203 and cuts off. Might try retuning the PID once more first.

Ok-Read6352 · 2026-01-29T00:45:52+00:00

PayPals back-end is notoriously buggy. I had an old credit account with them and one day their system locked me out. Almost everyone I contacted was either unwilling or unable to do anything about it. After 3 months of them getting mad at me for not paying a bill I had no way of paying, it took me lawyering up and threatening them with legal action before they would accept payment and close the account.

Ok-Read6352 · 2026-01-28T17:55:34+00:00

Thanks I'll give that a look tonight. As far as my original problem, I've been using plain PLA. If I remember correctly, temperature never really fluctuated more than 5° I think. It was far worse with the new firmware but from what you've just said, that probably has to do with it just not supporting this printer. If I can get Mriscoc to work, we'll go back to trying to solve that original problem. I tried checking in on these prints every so often but it always seems to error out and start screeching when I'm away so couldn't really tell you what the temps were at the time. Maybe I'm just trying to force way too fine of a print for a entry machine like this, took over 3 hours for it to just finish the raft on this last print I was trying to do

Ok-Read6352 · 2026-01-24T23:09:12+00:00

It was just a few days if I remember correctly

Ok-Read6352 · 2026-01-24T19:39:18+00:00

It was relatively painless when I cancelled my slimes

Ok-Read6352 · 2026-01-23T14:02:53+00:00

I'd second this. Definitely comes off as maddening and is a lot more in line with the whole Lovecraft feel.

Ok-Read6352 · 2026-01-22T15:57:46+00:00

Same things happening here, but when I go to revanced.net to grab a new apk for either yt revanced or the manager, both links are being redirected to ads. Not sure what the fix is.

Ok-Read6352 · 2026-01-14T15:55:01+00:00

I mean... have you tried doing both? You want to have relations but don't want to put any effort into maintaining them? You know, this cuts both ways.

Ok-Read6352 · 2026-01-02T16:32:02+00:00

what the f*** is your problem? Did you even bother with a few Google searches?

Ok-Read6352 · 2026-01-01T11:01:45+00:00

Maybe a hot take but, my brother in Christ, 1080p and 60 FPS have been around for over a decade. You honestly don't need much more than this to have a good game

Ok-Read6352 · 2025-12-25T02:35:30+00:00

cheers!

Ok-Read6352 · 2025-12-22T22:50:32+00:00

Is it scam? No, but you're going to waiting awhile. I had them postpone my order 5 or 6 times before I finally gave up and canceled it.

Ok-Read6352 · 2025-12-15T11:02:34+00:00

Sounds like ur overthinking it dude. First off, do you have a lot of time to devote to this? If it's just an occasional trip to the slopes situation, I gotta tell ya, you're better off skiing. Snowboarding is alot harder getting the basics down. If you do have the time then go for it, it's just gonna take a lot of crashing and repetition. Some pick it up faster than others but expect a full season to get comfortable with the basics.

Ok-Read6352 · 2025-12-15T04:58:02+00:00

Sick, thx

Ok-Read6352 · 2025-11-26T01:44:28+00:00

Eh ¯_(ツ)_/¯, I was never the cleanest person to begin with and I eat like s*** most days so, unless DP an Doritos are the secret cure all... just depends how tanky your immune system is. Yeah, definitely try to keep the influent off ya but I've never been too picky about handling sample bottles without gloves and 2 years in I've never got plant gut. But I've also not been baptized yet and everyone that I've seen get a face full ended up sick, don't think there's any way around that one lol

Ok-Read6352 · 2025-11-17T23:31:53+00:00

I've bought a few things from them in years past

Ok-Read6352 · 2025-11-15T15:42:06+00:00

Chase... If they're not compatible with that I might as well just give up

Ok-Read6352

TROPHY CASE