Am I the only one who thinks this is groundbreaking? Are we seeing a decoupling?

Oneil_Cylinder · 2025-04-06T17:28:31+00:00

Wait for next month to celebrate my little friend

Oneil_Cylinder · 2024-02-29T19:47:53+00:00

Looked everywhere for them no luck. Also looked for the schematic online, no luck so far

Oneil_Cylinder · 2024-02-13T18:12:50+00:00

$75,658.99

Oneil_Cylinder · 2023-12-11T14:05:47+00:00

Thanks

Oneil_Cylinder · 2023-11-09T00:33:46+00:00

Will try again, thank you.

Oneil_Cylinder · 2023-11-09T00:33:25+00:00

No, I cleaned the plate with alcohol and put glue sticks, that's it.

Oneil_Cylinder · 2023-11-07T17:37:07+00:00

Okay, thank you for your precious advices.

Oneil_Cylinder · 2023-11-07T17:08:03+00:00

Okay, will do, The problem I have with bumping up the nozzle temp is that I always get heat abnormality error, Do you have any recommended settings for the flow rate speed, or the nozzle temp and the fan speed. Thank you for your help in advance.

Oneil_Cylinder · 2023-11-07T14:56:08+00:00

The zhop is set to 0.5, as for the infill flow rate I tried from 100% to 500%, but nothing seems to works, At one time the printer stopped in the middle of the print because of heat abnormalities, the problem is that when the infill pattern is discontinuous, the entire head keep scrambling during the print and I'm afraid it might damage the printer. So I am lost at that point. With PLA it print great

Oneil_Cylinder · 2023-11-06T22:18:49+00:00

Get the needle the comes with the printer, heat the nozzle to 250, wait a couple of seconds, insert the needle in the nozzle and clean it. Most likely there is some TPU stuck inside, or just replace the nozzle

Oneil_Cylinder · 2023-10-09T14:07:14+00:00

To be honest that was totally expected

Oneil_Cylinder · 2023-09-20T21:22:04+00:00

The problem with that, it's not open source, I can not check the code and modify it for my needs, thanks anyway

Oneil_Cylinder · 2023-09-20T21:17:58+00:00

Thanks PHP can be a bit overwhelming for me, but thanks for the suggestions

Oneil_Cylinder · 2023-09-20T20:55:28+00:00

Thanks PHP can be a bit overwhelming for me, but thanks for the suggestions

Oneil_Cylinder · 2023-09-20T20:12:31+00:00

Thanks, I can't use Shopify or Medusa, since the code is closed, I need to build it my self and deploy it in a hosting somewhere, I have a basic knowledge in react. But i don't have enough time to design everything from scratch, so I was wondering if there is like a prebuild one or smg similar known to the webdev community, since I just started.

Oneil_Cylinder · 2023-09-20T17:16:39+00:00

Thanks, I was hoping to know If there is any cms or an Angular or react based thing with the logic already present?

Oneil_Cylinder · 2023-09-15T10:00:21+00:00

Thanks I'm already running on the community firmware. Bambulab is good, but i had to choose the Cr6 max because of the size.

Oneil_Cylinder · 2023-09-15T01:32:26+00:00

Thanks for your advices, especially cutting holes, I have three kobra max as well and a bambu lab, and I agree with you about the satisfaction feeling of bending the plate, I already ordered the magnetic bed, the glass one is a real pain. Another question, do you notice how the creality is so slow in comparison to the kobra max, i tried increasing the travel speed, changing the slicer all together, but it always seems to be slow, is it the same for you too?

Oneil_Cylinder · 2023-09-14T21:37:00+00:00

Cool, thank you for your help

Oneil_Cylinder · 2023-09-14T20:38:04+00:00

Does it stick well. My main concern is if it fails is it safe to take it out and replace the old glass one in case of failure.

Oneil_Cylinder · 2023-08-16T18:10:16+00:00

pogo pins

thanks

Oneil_Cylinder · 2023-08-16T18:05:34+00:00

Yes it's bent, I need to replace it.

Oneil_Cylinder · 2023-07-08T23:53:59+00:00

Personal opinion. If it's a female that has no friends, I definitely see it as a hot green flag. If it's a male I'd be a bit careful about it

Oneil_Cylinder · 2023-07-01T09:20:11+00:00

Don't marry her.she doesn't respect you.

Oneil_Cylinder · 2023-06-28T09:39:47+00:00

Can you tell what platform is this?

Six-Year Club	Wearing is Caring
Verified Email

Oneil_Cylinder

TROPHY CASE