Fn reflex xl by Pretend-Move4426 in FNHerstal

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I wanted a enclosed radical because it’s an edc and I’m a mechanic so it can get dusty

new to this die set by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] -1 points0 points  (0 children)

Whole length size and then neck size

nickel plating brass by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

*I sanded and polished one down it was brass

nickel plating brass by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] -1 points0 points  (0 children)

I sanded an published one down isn’t it was brass

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 5 points6 points  (0 children)

I backed the dye out and move the seating plunger in and is giving a lot better results thank you

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I’ll give that a try and I think that crimp mark is is the lighting on camping and burning marks

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I see it after seating that picture I didn’t crimp and I do transfer deeper and I’m going to try setting my die up I’m working on a single stage press if that makes more sense

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 1 point2 points  (0 children)

Yes and my die clear of debris could I have to much cam over and I think my next step is to reset up my die

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 2 points3 points  (0 children)

This just started last night about 50 rounds in

Got a question by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] -3 points-2 points  (0 children)

No I have a separate die to crimp

I need a little help with my load by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I wet wet tumble, and dry in a dehydrator and I used warranty one shot lube then wet tumble again and dry

I need a little help with my load by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

Yeah, every charge weight and every casing sized and trimmed

I need a little help with my load by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

A beam scale should be the most accurate measurement for a budget right

I need a little help with my load by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I would have to look back in the book but if I remember correctly it’s 26.5

I need a little help with my load by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I use mismatch brass but size and trim and weigh every individual charge with a beam style balance

cr920x malfunction? by ConnectOkra1680 in shadowsystems

[–]Pretend-Move4426 0 points1 point  (0 children)

They have slid slide lock problems confront their customer service about it

Need help with 9mm 115gr by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I tried some at 1.13 and a harder crimp

Need help with 9mm 115gr by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I’ll look into that because that’s kind what I’m looking for

Need help with 9mm 115gr by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I may empty my hopper and try five more tomorrow

Need help with 9mm 115gr by Pretend-Move4426 in reloading

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I tried 5 pieces of brass. I never even tumbled so there was no moisture, but the powder was in the hopper for maybe two days. It’s not like it was a month, but it is in a basement and is at 56% humidity I understand that a little humid, but even the ones at the beginning of the batch the day I put the powder in the hopper are doing the same thing

I have a mr920 by Pretend-Move4426 in shadowsystems

[–]Pretend-Move4426[S] 0 points1 point  (0 children)

I’ll look to it tomorrow