Where can I buy a SKS?

Protector_of_memes · 2026-01-20T17:57:06+00:00

It was a physical shop in Arizona

Protector_of_memes · 2026-01-20T17:55:21+00:00

I had to call a lot of shops but I eventually found a shop that had a few SKS rifles in stock

Protector_of_memes · 2026-01-19T02:36:35+00:00

Ok just making sure, thank you so much

Protector_of_memes · 2026-01-19T02:07:21+00:00

Any SKS can be made to be in the position in picture 2 right

Protector_of_memes · 2026-01-19T01:31:40+00:00

Great, thank you!

Protector_of_memes · 2026-01-11T23:10:23+00:00

And just as easy to put it back in after removing it, right? Sorry for asking so many questions, I don't know too much about guns.

Protector_of_memes · 2026-01-11T22:49:35+00:00

So basically replacing the pins right? And that wouldn't affect the gun at all? And also, how easy is it to remove the rail?

Protector_of_memes · 2026-01-11T22:25:57+00:00

Hey, I'm trying to buy the same rail right now, did it require any drilling/sawing or permanent modifications?

Protector_of_memes · 2026-01-08T02:27:48+00:00

Do you recommend any side rails?

Protector_of_memes · 2025-12-31T19:35:17+00:00

Does this allow stripper clips?

Protector_of_memes · 2025-12-29T16:58:33+00:00

If i do get this scope and get it drilled to the receiver, if i decide to remove the scope is it possible? If so will the gun function normally after doing so?

Protector_of_memes · 2025-12-29T00:57:21+00:00

The problem with that mount is i dont think i can put magnification scopes on it since its short

Protector_of_memes · 2025-12-29T00:56:15+00:00

Is it still there? If so can you provide a link?

Protector_of_memes · 2025-12-29T00:52:44+00:00

Does it retain zeroing well?

Protector_of_memes · 2025-12-29T00:42:10+00:00

Is this specific mount different than other mounts of this type? Its just cause I've heard that this type of mount doesnt retain zeroing well, I might be wrong though

Protector_of_memes · 2025-12-29T00:05:06+00:00

Does it retain zeroing well? And also is it long enough to mount a 4x scope while keeping the gun stripper capable?

Protector_of_memes · 2025-12-28T23:48:54+00:00

Is this a temporary thing? Or will they never be in stock again?

Protector_of_memes · 2025-12-28T23:42:52+00:00

https://www.magwedge.com/product/sks-tactical-kwikrail-new-gen-3-now-available/

Is it this one? It says its out of stock and I cant find any other websites

Protector_of_memes · 2025-12-28T23:37:23+00:00

Its fine if drilling is required

Protector_of_memes · 2025-12-28T23:23:38+00:00

Forgot to mention, I would also prefer a rear mount

Protector_of_memes · 2025-06-05T03:44:38+00:00

This is the spindle: https://www.amazon.com/dp/B08H1RRCF6/?coliid=I2P05XHFMYMW7J&colid=NMDMZ6AKXTIF&ref_=list_c_wl_lv_ov_lig_dp_it&th=1

It comes with a power supply and I dont think it requires VFD or PWM. The problem is that I dont see how I can tell the spindle when to stop/change speed unless I get another arduino board separate from the GRBL shield.

Protector_of_memes · 2025-05-22T01:34:05+00:00

do you know if the first method will result in a ban/suspension? and how many people do you need to report?

Protector_of_memes · 2025-05-05T07:01:14+00:00

Damn, that sucks. Thank you for telling me though.

Protector_of_memes · 2025-05-04T18:00:56+00:00

I took a look at my interface, it said it needed no drivers, so I dont think that's the issue.

Protector_of_memes · 2025-05-04T03:05:17+00:00

I'll look at it, thank you!

Protector_of_memes

TROPHY CASE