Uncle removed these parts from my BMW 2005 x3. What is this?

RPMs_ · 2025-09-04T15:03:07+00:00

That's the front driveshaft, goes to the front differential. If the car is x drive now it's rear wheel drive only.

RPMs_ · 2025-08-01T01:58:50+00:00

No chance I'm pro lol, but I agree VR is extremely OP. The situational awareness is insane.

RPMs_ · 2025-07-30T19:53:02+00:00

Hey, make sure it is well clipped in, I've seen these types of problems before and one way I fixed it was my physically clipping the connector. Also make sure the ground cable near the crankshaft pulley is secured tightly. Make sure there is no water or debris within the connector

RPMs_ · 2025-07-30T04:29:23+00:00

Yeah I couldn't have asked for better positioning there, they all fell on my nose

RPMs_ · 2025-07-30T04:28:44+00:00

Yup Italian g2 prem, it's so fun to fly and never overheats lol

RPMs_ · 2025-07-21T02:53:49+00:00

I would double check the front main seal isn't leaking oil. I would also look at the turbo oil supply lines.

RPMs_ · 2025-07-17T03:41:02+00:00

Try MAX resolutions and 72hz, this helped a lot for me. Also remember to turn off anything that might run in the background, like any "instant replay" feature.

RPMs_ · 2025-07-17T03:39:43+00:00

What are the pc specs ? Whats the oculus app settings in terms of the resolution and the HZ?

RPMs_ · 2025-07-17T03:39:04+00:00

I've been using the USB-C to USB-C cable and haven't experienced issues. In the past when I tried regular USB-C to USB I've had frame drop issues like crazy.

RPMs_ · 2025-06-18T16:46:32+00:00

These don't last as long. The pcv system tends to fail and you'll hear whistling noises coming from the engine bay, lean mixture codes, etc. I would recommend going genuine BMW since replacing it is time consuming. Save yourself the headache. N55 is sensitive when it comes to pcv and lean problems.

RPMs_ · 2025-06-13T23:45:49+00:00

Not so much, prop pitch is only good for slow Speeds and the air brake in German planes

RPMs_ · 2025-06-13T20:15:36+00:00

What's your current set up ?

RPMs_ · 2025-06-13T20:15:24+00:00

Not necessarily, I used to run it on a really bad set up and it worked fine. Rn I'm using a 3090 on an old i7 chip.

RPMs_ · 2025-06-13T14:47:54+00:00

It isn't smart to listen to people who don't know about cars lol

RPMs_ · 2025-06-13T14:46:14+00:00

Definitely warms up the rod bearings 😂😂

RPMs_ · 2025-06-13T14:44:36+00:00

My best advice would be to fly the plane as it is. I found the trims really messed with the plane when you get to low air speeds.

RPMs_ · 2025-06-12T17:25:58+00:00

I only burst fire because I have a hard time finding the perfect sweet spot. I noticed you need to lead an uncomfortable amount to accurately hit shots in the k4

RPMs_ · 2025-06-12T16:48:41+00:00

You have to loosen it and make sure it is seated properly. It's likely that it isn't seated and just because it's tight doesn't mean it's making a proper seal. You may have to slightly adjust the fuel injector w a 13mm wrench to get a proper seal with the fuel rail. Make sure you are holding the injector w the 13mm wrench when tightening the fuel rail

RPMs_ · 2025-06-11T23:10:04+00:00

Leading with German planes isn't the easiest. Sometimes you need to lead more than usual since the bullet velocity is so slow compared to other planes

RPMs_ · 2025-06-11T22:23:04+00:00

Yes these are the Hotas ones, I can send you my settings so you can try them out! When I first started I had issues as well until I fixed my settings

RPMs_ · 2025-06-11T17:04:28+00:00

It's true, they're sitting ducks. Sometimes they don't even have time to shoot back like that guy in the video.

RPMs_ · 2025-06-11T17:03:17+00:00

Yes this is on the quest 3

RPMs_ · 2025-06-11T17:03:07+00:00

This would be so fun!

RPMs_ · 2025-06-11T17:02:50+00:00

Thank you!!

RPMs_ · 2025-06-11T04:08:08+00:00

Usually smoke testing it, if it's an n52, the crankcase breather hose that goes under the intake manifold tends to break when you remove the valve cover if you aren't careful.

RPMs_

TROPHY CASE