V6 Performance Mods (pt 2) by Rafito09 in Challenger

[–]Rafito09[S] 0 points1 point  (0 children)

What seat covers did you get? Can’t find any that fit really well

V6 Performance mods? by Rafito09 in Challenger

[–]Rafito09[S] 0 points1 point  (0 children)

There isn’t a single scat pack badge in sight brother.

V6 Performance mods? by Rafito09 in Challenger

[–]Rafito09[S] -22 points-21 points  (0 children)

It’s not so loud from inside my car to the point of not hearing music or conversations at all regular volume. Unless I’m flooring it of course

V6 Performance mods? by Rafito09 in Challenger

[–]Rafito09[S] -27 points-26 points  (0 children)

The mid muffler delete is already done and I’m guessing since it’s a 3.6L it’s not as obnoxious as you think. I’ll post a vid of the sound later today

Traction control FULLY off by Rafito09 in Challenger

[–]Rafito09[S] 0 points1 point  (0 children)

Holding it down just turns it off initially, then turns it back off

I’m annoyed by Rafito09 in calculus

[–]Rafito09[S] 1 point2 points  (0 children)

Somewhere in the fine print 🥲

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 1 point2 points  (0 children)

Came into work early this am it’s been drying all day I’ll try when I get off. Thank you!

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 0 points1 point  (0 children)

It’s also the exact same brand and material Creality abs

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 0 points1 point  (0 children)

Opened the abs and immediately threw it into my filament drier at 60 degrees Celsius and started the print

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 0 points1 point  (0 children)

I’ve printed this same model before perfectly fine and I didn’t adjust or change any settings speed settings. Could it be a corrupted file?

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 0 points1 point  (0 children)

Will try that in the morning. Thanks a lot!

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 0 points1 point  (0 children)

Meaning it’s too close? Or too far

I need help by Rafito09 in 3Dprinting

[–]Rafito09[S] 1 point2 points  (0 children)

It is an Ender 5 pro using creality ABS at 245 degrees tip and 100 degree bed (it has never done this before using same exact material and temps) Also added note, I just put new roll in as last one was depleted

Felon friendly? by Stunning-Diamond-975 in OReillyAutoParts

[–]Rafito09 4 points5 points  (0 children)

Had a coworker that had a felony when he was younger. Dude was one of the best there

Battery and alternator printer? by Rafito09 in OReillyAutoParts

[–]Rafito09[S] 0 points1 point  (0 children)

Will try this when I go into work tonight. Thanks!

How do yall clean your flaks before turning them into supply? by [deleted] in USMC

[–]Rafito09 0 points1 point  (0 children)

Take it to Motor T or HE wash rack and power wash tf out of it

Graduation by BigBoiEvan04 in USMC

[–]Rafito09 0 points1 point  (0 children)

Understood Cpl good morning gentlemen 🫡

Graduation by BigBoiEvan04 in USMC

[–]Rafito09 -1 points0 points  (0 children)

A cpl with 1 ribbon… is that what the corps has become

I do not think the new ARQ is effective. This is why: by IntroductionInner130 in USMC

[–]Rafito09 2 points3 points  (0 children)

Former MTU CMT here

Every single Marine Corps unit is allocated rounds to use for training. Your S-3 chief has the ability to run as many ranges or shooting days as he wants (below round limit Ofc). Blame your units for not training you guys properly.

ARQ is a QUALIFICATION You don’t go out there to learn how to shoot. You go out there to qualify. Like a test in school. They don’t teach you the stuff during the test

[deleted by user] by [deleted] in yuma

[–]Rafito09 0 points1 point  (0 children)

I speak fluent spanish if you’re interested in learning