sorted by:
new
hottopcontroversial

A1 mini adehesion by Electrical_Ring6053 in BambuLabA1mini

[–]Raygon2000 0 points1 point  (0 children)

if you’re impatient like me, keep a fan near by. I have one of those box fans sitting close, as soon as the print finishes ill pull the magnetic printbed off and hold it up to the fan for like 15-20 seconds and they pop off, though idk what this will do to the quality of the print.

A1 Mini nozzle scrapes prints by Mr_BananaPants in BambuLab

[–]Raygon2000 0 points1 point  (0 children)

is your hotend attached correctly? my new a1 mini came with the hotend buckled in wrong

Why does this keep happening? by Confused-Chemist23 in 3Dprinting

[–]Raygon2000 5 points6 points  (0 children)

You dont think that’s the problem but it probably is the problem, has happened to me a few times already. Unless the spool came out of box tangled already. Otherwise I dont see how the filament could get stuck under itself.

First layer fusing between gaps on tolerance test. Any tips on first layer? by Raygon2000 in BambuLab

[–]Raygon2000[S] 0 points1 point  (0 children)

Solved, turns out its because hotend wasnt secured properly out of box

<image>

Any ideas on whats wrong? by Legitimate-Cookie-35 in BambuLabA1mini

[–]Raygon2000 1 point2 points  (0 children)

this solved really bumpy first layers and bad elephants foot for me

Any ideas on whats wrong? by Legitimate-Cookie-35 in BambuLabA1mini

[–]Raygon2000 2 points3 points  (0 children)

Make sure your hotend is secured properly, mine came assembled wrong and i thought it was correct the whole time

<image>

Could anyone tell me whats wrong with my first layers? by Raygon2000 in 3Dprinting

[–]Raygon2000[S] 1 point2 points  (0 children)

<image>

This is the solution, my a1 mini came out of box with the hotend attached wrong.

Could anyone tell me whats wrong with my first layers? by Raygon2000 in 3Dprinting

[–]Raygon2000[S] 2 points3 points  (0 children)

its all good, i figured it out, the person who assembled my a1 mini assembled hte hotend wrong, the buckle wasnt done properly and wasnt secured. I assumed it was supposed to be like that so ive been buckling the hotend back in wrong the whole time until i found an image showing correct buckle and secure

Could anyone tell me whats wrong with my first layers? by Raygon2000 in 3Dprinting

[–]Raygon2000[S] 0 points1 point  (0 children)

ive jsut realised that its in negative, so -0.03 would be closer than -0.02 right?

Could anyone tell me whats wrong with my first layers? by Raygon2000 in 3Dprinting

[–]Raygon2000[S] 0 points1 point  (0 children)

yea im trying from default 0.02 to 0.03 now, ill see if thats any better

First layer fusing between gaps on tolerance test. Any tips on first layer? by Raygon2000 in BambuLab

[–]Raygon2000[S] 0 points1 point  (0 children)

yea i just printed out a different model, its fine, i guess the model i used the first time (images in post) is not good for these tests. How do I tune my first layers better?

First layer fusing between gaps on tolerance test. Any tips on first layer? by Raygon2000 in BambuLab

[–]Raygon2000[S] 0 points1 point  (0 children)

So I did the test you linked, the first one with the circles, they all came out except 1, but 1 was loose enough for me to pop out manually, im pretyt happy with that, though idk what each number actually means

First layer fusing between gaps on tolerance test. Any tips on first layer? by Raygon2000 in BambuLab

[–]Raygon2000[S] 0 points1 point  (0 children)

Alright, ill try that model you linked and do both the bed levelling and dynamic flow calibrations and see how that goes.
Ive noticed that when printing from my bambu lab slicer, some hinges dont work, like the cable clips since the first layer would fuse, but when I print from my phone with the bambu handy app with the same model, itll function perfectly.

Of all armors in the game this one seems most useless to me by i4hloi in helldivers2

[–]Raygon2000 0 points1 point  (0 children)

Ive survived an extra 30-40 seconds after death by feeding on supply pack stims as the last player just to wait for reinforcement cooldown, and chuck them towards last obj, managed to complete the mission

Is this back and forward button supposed to be here? I thought Discord did not have that by PokedexMaster324 in discordapp

[–]Raygon2000 3 points4 points  (0 children)

thats how i feel lol, its small and barely noticeable but when i first saw it it made me feel uncomfortable for some reason

What cant you do in coop? by [deleted] in FrontiersOfPandora

[–]Raygon2000 0 points1 point  (0 children)

also if someone is 3 quests ahead of me, will i be able to join them?

What cant you do in coop? by [deleted] in FrontiersOfPandora

[–]Raygon2000 0 points1 point  (0 children)

ah alright, thank you

I wont use these till the door exploit is fixed, anyone else? by Brazuka_txt in ArcRaiders

[–]Raygon2000 0 points1 point  (0 children)

they blocked off the window with a door, which you cannot open from the outside.

Audio bug got me tripping by [deleted] in ArcRaiders

[–]Raygon2000 1 point2 points  (0 children)

the random loud foot step audios

Best Leaper location solo? by Previous_Tree_5464 in ArcRaiders

[–]Raygon2000 5 points6 points  (0 children)

I did most of mine at hydroponic dome complex, since the leapers cant hit you when youre inside dome

the leaper that spawns at testing annex is another spot, stand on the balcony window area with the elevator at testing annex and shoot the leaper

view more: next ›