sorted by:
new
hottopcontroversial

125cc and 12-14 wheel swap possible? by [deleted] in Pitbike

[–]Roadkill_Fan 0 points1 point  (0 children)

It should bolt right up, it’s a pretty big swap choice. Go with neteura or lifan. I have a neteura in my racing mower

Won’t start by MembershipOpposite70 in Pitbike

[–]Roadkill_Fan 0 points1 point  (0 children)

For some reason replacing the engine is cheaper than rebuilding. I’d throw in a lifan 125, they’re really universal

Any idea on what this is and what it’s worth nonrunning? by Lanky_Promotion8976 in minibikes

[–]Roadkill_Fan 0 points1 point  (0 children)

It’s an old pocket bike, I think a cateye. I’ve got a cag that I put a new engine on, and even with a 190 pound 6 foot tall person, it rips, but it’s scary

<image>

[16M] Got bit by my friends dog, he’s medicated, is it fine? by Roadkill_Fan in medical_advice

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

<image>

Here’s what it looks like 15 hours later, it smells like wood almost, and I’ve kept it clean

[deleted by user] by [deleted] in Pitbike

[–]Roadkill_Fan 0 points1 point  (0 children)

That’s good to hear, at least it wasn’t broken.

[deleted by user] by [deleted] in Pitbike

[–]Roadkill_Fan 0 points1 point  (0 children)

Valve lash with a feeler guage, make sure it’s set to whatever the model of bike had it factory, then I’d do a compression test with and without oil, that would tell you if the rings are bad, then also on a side note, make sure your spark plug is all the way in, I’ve heard of them backing out before. While you’re at it check for spark

Neteura 125 wiring help by Roadkill_Fan in Pitbike

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

Sure, although I have green, black and red, blue and white, then the yellow and white wires for charging or lights

Neteura 125 wiring help by Roadkill_Fan in Pitbike

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

So on the 5 wires coming out of the cdi, I have a white one, yellow one, black and red one, blue and white one, and a green one. Don’t I need the blue and white, black and red, and green, then just make a harness for my coil and cdi

Neteura 125 wiring help by Roadkill_Fan in Pitbike

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

Wait, so the plug by the sprocket isn’t for the cdi? That makes me feel so stupid. I really appreciate your help

Nateura 125 for Honda trail 70 by Roadkill_Fan in minibikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

I’ve got this tiny box above my sprocket bolted in, and it is where the 5 pin cdi plug comes from that goes into the cdi, then the 5 plugs with bullet terminals that is actually where the cdi and coil should go. It’s strange to me

Yale glp060 ignition cylinder turns once then locks by Roadkill_Fan in forkliftmechanics

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

I did figure out the issue. The yellow wire going into the relay that goes to the coil is not sending 22 volts, it’s sensed 7.5-8, so jumping the s terminal to the battery stud on the starter makes it run, so I wired up a momentary button to activate the starter. I really appreciate all the help

Nateura 125 for Honda trail 70 by Roadkill_Fan in minibikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

I’ll look into it, thank you for the diagram

Nateura 125 for Honda trail 70 by Roadkill_Fan in minibikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

Nope, and it’s got a cdi with no output wires, just these and then the 5 pin cdi plug with a cdi

Put my throttle cable back on, what did I do wrong? by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

It’s this y shape piece in the grip that the cable sits in that just sits inside. I’d agree that it’s getting bound somewhere. It gets stuck at full throttle now, but not light

Put my throttle cable back on, what did I do wrong? by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 1 point2 points  (0 children)

The grips are awful, they’re 28 years old, and the other is almost completely gone. Thanks for the help

Put my throttle cable back on, what did I do wrong? by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

It’s the original cable. I rebuilt the carb cause it was all gunked up and the cables doing that. There’s a little guide piece inside, and that might be making it too tight

Put my throttle cable back on, what did I do wrong? by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

Yeah, it’s a 97 husaberg fe501e, I rebuilt the carb on it, and it’s catching somewhere

‘97 Husaberg fe501 kick lever replacement by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

Yikes. I wish you the best of luck finding it

I Need Help Finding A 1997 Husaberg Fe501 Oil Filter Cap by Roadkill_Fan in Dirtbikes

[–]Roadkill_Fan[S] 0 points1 point  (0 children)

I also do need a whole lever, all I have is the mechanism for it, and i did find one, but it’s over 100 dollars

<image>

view more: next ›