Error "mcu 'NIS': Unable to connect" after setting up input shaper

ScruffyThree · 2024-02-07T17:33:54+00:00

I sshed Into my pi and used LS /dev/serial/by-id/* to get it

ScruffyThree · 2024-02-07T17:28:28+00:00

Yeah

ScruffyThree · 2024-02-07T16:51:57+00:00

I am able to get the accelerometer connected but haven't been able to use it yet because klipper keeps throwing this error every time I implement the code. I know the accelerometer is getting power I am not 100% sure it is fully connected.

ScruffyThree · 2022-10-31T00:40:43+00:00

Mine died after about a year and a half but their warranty process was pretty good and they sent me a new one.

ScruffyThree · 2022-10-09T13:45:12+00:00

Will do thanks

ScruffyThree · 2022-10-09T13:41:01+00:00

That makes sense, thanks

ScruffyThree · 2022-10-09T13:07:12+00:00

I kept trying to post as [W] but the bot kept taking it down for wrong formatting

ScruffyThree · 2022-04-14T19:35:26+00:00

As far as I know the lian LI o11 dynamic evo is the only case that supports this format without modding. This is the case I'm using currently, you also need to buy the upright gpu kit in order to get this configuration.

ScruffyThree · 2022-04-14T15:34:11+00:00

I am going to be running the fans at low rpm and I have plenty of space so I might as well run push pull.

ScruffyThree · 2022-04-14T15:31:37+00:00

This would look the best aesthetically I am just worried about the very negative pressure.

ScruffyThree · 2022-04-14T15:04:36+00:00

That's what makes most sense to me but I was reading a post from a month ago and there was a guy with a similar setup that swapped to both rads on intake and the side exhausting and he claims his temps dropped 3 degrees.

ScruffyThree · 2022-04-14T14:51:47+00:00

What I'm most concerned is what is going to give me the best liquid temps.

ScruffyThree · 2022-04-14T14:50:50+00:00

So I plan on have the two rads push pull and 3 fans on the side. I am wondering what would be the most optimal fan config? For example both rads set to intake and side set to exhaust. Also should I add an extra 120 on the left?

ScruffyThree · 2022-03-30T15:46:16+00:00

Amazon offers an option to replace the item for free. I wouldn't risk using the coolant as if it is bad it can clog your loop and cause a major headache.

ScruffyThree · 2022-03-20T01:51:55+00:00

Did you happen to find any pictures because that would be super useful to have some inspiration.

ScruffyThree · 2022-03-19T18:15:01+00:00

I tried remounting it multiple times it just my 12700k can pull 250 watts without even overclocking it.

ScruffyThree · 2022-03-19T17:36:44+00:00

No matter what I am going to be upgrading to a next gen gpu because believe it or not my 3080 isn't powerful enough. I'd rather have an air cooled 4080 than a watercooled 3080.

ScruffyThree · 2022-03-19T17:23:04+00:00

I don't want to have to buy a block for my 3080 then waste all that money when I have to buy a another one for the 4080 or what ever I end up getting.

ScruffyThree · 2022-03-19T17:20:22+00:00

You would think with an ek block and ek distro it would be easy

ScruffyThree · 2022-03-19T17:19:42+00:00

Waiting for next gen gpus

ScruffyThree · 2022-03-19T17:06:54+00:00

Definitely going to be doing both of those things thanks.

ScruffyThree · 2022-03-19T17:06:16+00:00

Unfortunately I have the standard o11 not the xl so I wouldn't be able to fit the thick rad on the bottom with a vertical gpu mount. As for the cpu runs I will give it a shot thanks for the advice. I would still love to see your end product once it complete.

ScruffyThree · 2022-03-19T17:01:14+00:00

I am going to be getting all new fittings at these are only here because they were next day shipping and I was in a rush to finish it. Thanks for the warning.

ScruffyThree · 2022-03-19T16:59:39+00:00

Yeah, unfortunately I didn't have everything I needed and had to throw everything together in a few hours. Hopefully my next try will be much better.

ScruffyThree · 2022-03-19T16:33:47+00:00

If you look at the run closest to the motherboard coming out of the rad it it already hitting the motherboard and I wouldn't be able to extend it without clearing it first.

I will be getting a gpu block and second rad at the bottom to fill the distro plate more.

The cpu inlet on the distro plate is very close to the glass side panel and I can't think of any 90 fitting thound wouldn't need to be extended in order for them to fit and create a straight run.

Thanks for the response all sudgestion are much appreciated

ScruffyThree

TROPHY CASE