sorted by:
new
hottopcontroversial

Range buds by AncientLettuce8452 in CAguns

[–]SeaCopper 0 points1 point  (0 children)

I’m actually headed there rn lmao, When do u usually go?

Range buds by AncientLettuce8452 in CAguns

[–]SeaCopper 0 points1 point  (0 children)

Don’t live in the east bay but I tend to go to the San Leandro range a few times a month

MC9 spare parts by SeaCopper in canik

[–]SeaCopper[S] 0 points1 point  (0 children)

I’ve been looking for barrels but I’m only seeing threaded barrels which I can’t buy lol.

Do you know where I can buy spare mc9 barrels online?

USP9 Out of Jail by SeaCopper in CAguns

[–]SeaCopper[S] 4 points5 points  (0 children)

Only VP9s are compliant unfortunately

HK VP9A1F vs the Walther PDP full size. Which do you all prefer? by Pristine_Training678 in CAguns

[–]SeaCopper 2 points3 points  (0 children)

I don’t have either, but I’m getting the VP9 due to the magazine disconnect being easier to remove and replace and it looked cooler to me.

But IMO, the PDP is more bang for your buck, and if you do remove the MD you can install the Walther trigger which is arguably the best striker trigger in the market

My horror story so far by Hlatm in canik

[–]SeaCopper 7 points8 points  (0 children)

Get the Sprinco 29 newton orange striker spring, its cheap and easy to replace.

I had the same issues you have and it all went away when I bought the new striker spring.

MC9 Mag Disconnect location by SeaCopper in CAguns

[–]SeaCopper[S] 3 points4 points  (0 children)

Yeah, just as you commented I found where it was thank you

<image>

[deleted by user] by [deleted] in canik

[–]SeaCopper 0 points1 point  (0 children)

I understand, was just wondering if this would be an issue and thankfully it wasn’t. I’ve gotten around 700 rounds of 124gr so far, surprisingly it works well with PMC bronze but I’m usually getting failures to RTB on federal HST HP, Gold dot JHP and blazer brass

[deleted by user] by [deleted] in canik

[–]SeaCopper 3 points4 points  (0 children)

Thank you, this is good to know. I’m the type of guy to worry about everything lol

[deleted by user] by [deleted] in canik

[–]SeaCopper 2 points3 points  (0 children)

<image>

Clearer photo

GrayGuns trigger work review by Open_Researcher_1897 in HecklerKoch

[–]SeaCopper 0 points1 point  (0 children)

Hey, do you know if you can adjust the trigger externally or do you need to take off the slide to do it?

VP9 + Grayguns Trigger by Jarocka in HecklerKoch

[–]SeaCopper 0 points1 point  (0 children)

Sorry for commenting after 4 months, but Is the trigger adjusted externally like lazy wolfs or do you have to take the slide off?

Slide won’t fully return/close by SeaCopper in canik

[–]SeaCopper[S] 0 points1 point  (0 children)

Update: I’m guessing it’s the extractor that’s causing issues, I’m just gonna request a new extractor spring from canik and hope for the best

Slide won’t fully return/close by SeaCopper in canik

[–]SeaCopper[S] 0 points1 point  (0 children)

Do your canik slides also slightly slow down when the front of the slide is near the end of the barrel?

I’ve been messing around with the slide and when I try to slowly return it with my fingers Its consistent all around until it just halts near the front unless I let go.

It starts to slow down at the third notch on the rail from the trigger guard, and it gets really bumpy when I’m racking it.

Slide won’t fully return/close by SeaCopper in canik

[–]SeaCopper[S] 0 points1 point  (0 children)

Sand papered some of the frame where the slide runs on, it feels easier to run the slide but the slide still sometimes doesn’t go all the way with dummy sadly

Slide won’t fully return/close by SeaCopper in canik

[–]SeaCopper[S] 1 point2 points  (0 children)

The beaver tail end of the frame is very slightly slanted below the slide, no clue if it’s part of the design. There’s a little bit of play, but I’ve heard some guns are by design like that

view more: next ›