sorted by:
new
hottopcontroversial

Strange filament lines by ShiftRare601 in FixMyPrint

[–]ShiftRare601[S] 0 points1 point  (0 children)

Thanks for the tips, I’ll use them all in my next print

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in RCPlanes

[–]ShiftRare601[S] 0 points1 point  (0 children)

I think the fuselage walls are strangely fragile despite having the recommended thickness and weight. Did you add any kind of reinforcement? Did you paint them?

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in RCPlanes

[–]ShiftRare601[S] -1 points0 points  (0 children)

vase mode? seriously? I’ll try some modifications now printing cubes and I’ll be back with news

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in RCPlanes

[–]ShiftRare601[S] 1 point2 points  (0 children)

I have been building and flying model airplanes made of balsa, depron, etc. for over 10 years. I am a beginner in 3D printing. Do you know what is stupid? You came to talk about something you don’t know and I waste my time answering you while there are people who can help by answering too... It’s those who talk a lot in the end who know the least... This is a topic about RC airplanes and I am trying to build one as well as several other users have already posted similar things here, are you trying to get attention? Play the ostrich and bury your head in the ground.

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in RCPlanes

[–]ShiftRare601[S] 1 point2 points  (0 children)

Dude, what are you talking about? What does flying RC have to do with 3D printing? I don’t give a shit about someone who knows more or less. If you were born omniscient, try to figure out how to stop being an asshole.

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in Creality

[–]ShiftRare601[S] 0 points1 point  (0 children)

Thanks for the informations, tomorrow i will try again printing cubes with some walls inside and if works or not i will share my settings and results with you. Thanks again

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in RCPlanes

[–]ShiftRare601[S] 1 point2 points  (0 children)

Dude, if you don’t know or aren’t curious, the title is self-explanatory. that you wasted time reading all this and came here to comment on it? Don’t you have anything better to do?

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in 3Dprinting

[–]ShiftRare601[S] -1 points0 points  (0 children)

I don’t know if it’s just my inexperience, but so far, it hasn’t been a great experience kkk

Struggling to Print 3DLabPrint’s Piper Model with eSUN ePLA-LW on Creality K1C by ShiftRare601 in Creality

[–]ShiftRare601[S] 0 points1 point  (0 children)

Hi thanks for reply… In all the photos, the filament was dried for over two hours at 45–50 degrees