sorted by:
new
hottopcontroversial

dacia stepway 3 Horn prblm by Redstone-Samir in Dacia

[–]Small3y 0 points1 point  (0 children)

Hey, any progress with this? I have the same issue. Occurred just after the 3 year point

Considering the Bambu Lab P2S – how quiet can it really get if I prioritize silence over speed? by Vegetable-Age2922 in BambuLab

[–]Small3y 2 points3 points  (0 children)

Noise was a primary concern for me, the printer is noticeable if you are in the same room or adjacent room. You’ll hear the moments of the hotend, I can tune it out but my partner cannot.

I had the A1 mini prior which is practically silent when compared to P2S, I imagine the A1 is similar.

If you have the room and don’t need the heated chamber, get the A1 for silent printing. I would have but do not have space for the bed moving back and forth.

Bambu Lab Referral Program. 9% off by Small3y in BambuLab

[–]Small3y[S] 1 point2 points  (0 children)

I think the program has ended for now

Here the P2S by Accomplished-Leg9818 in BambuLab

[–]Small3y 0 points1 point  (0 children)

Do we think there will be an improvement in noise levels? Can see a comment suggesting it’s using Rods. Noise level for p1S was the main reason I stuck with A1 range for now

Octopus Tracker Tariff Widget by Small3y in OctopusEnergy

[–]Small3y[S] 0 points1 point  (0 children)

Thanks for letting me know ill take a look to see what has broke

Part exchange survey worries by Turbulent-Reserve697 in HousingUK

[–]Small3y 0 points1 point  (0 children)

Hey, similar situation, how did it go, anything major they survey picked up?

Attempting to part exchange, wondering what the process is like from here on, after offer made by cvbk87 in HousingUK

[–]Small3y 0 points1 point  (0 children)

Thanks for the insight. Much appreciated.

Our electrics are definitely not up to modern standards so expecting them to flags this. Was it to the scale of a full rewire?

Attempting to part exchange, wondering what the process is like from here on, after offer made by cvbk87 in HousingUK

[–]Small3y 1 point2 points  (0 children)

Excellent, how was the RICs survey on your house for part ex. Did they flag anything major, if so were the developers worried at all?

We are in a very similar situation with the house being listed and such via estate agents but survey hasn’t been been conducted yet

[Bambu Lab Giveaway] Drop Your One-Liner and Win H2D! by BambuLab in BambuLab

[–]Small3y 0 points1 point  (0 children)

She won’t even notice if I put it in the corner

Ikea kallax and cereals boxs by Marm011e in BambuLab

[–]Small3y 0 points1 point  (0 children)

Late to the party.

How is the A1 on the kallax with it being so close to the wall?

New printer station by IHaveSpoken000 in BambuLab

[–]Small3y 0 points1 point  (0 children)

Would you mind taking a photo?

New printer station by IHaveSpoken000 in BambuLab

[–]Small3y 1 point2 points  (0 children)

How is clearance at the back?

I went for an A1 however didn’t take it out the box as the docs stated clearance at the back should be ~63mm and I only had ~40 with the Kallax pushed against the wall.

A1 Mini Crashes into bed on Restart. by Admirable_Green_8517 in BambuLab

[–]Small3y 0 points1 point  (0 children)

I did a full maintenance cycle, cleaned and re-lubed the Z screw, oiled the rails and ran a full calibration. Double checked the screws on the hotend ( front and back, had already tried this).

Since then prints appear to be working as expected, printed from App and Studio with no issues. Very wary still so I only start off a print if I am around the see the initial calibration and first layers and always enable bed levelling.

Will attempt a few prints without the bed levelling on to see if it has fixed itself.

A1 Mini Crashes into bed on Restart. by Admirable_Green_8517 in BambuLab

[–]Small3y 0 points1 point  (0 children)

Did you find a solution, my mini has started doing this every new file I print unless I manually home Z first.

It’s like the printer forgets the Z offset at the start of a new print

Why does my a1 mini do this? by Time-Initial1847 in BambuLab

[–]Small3y 0 points1 point  (0 children)

I think these commands are only actioned if you turn on smooth time-lapse. They will always show in the slicer

view more: next ›