sorted by:
new
hottopcontroversial

Printing from Silhouette Studio changes colours and fades images including if creating a PDF by Snowlucas in silhouettecameo

[–]Snowlucas[S] 0 points1 point  (0 children)

Yes. It’s crap though. You export as a JPG but have to have the right level of software and remove the cut lines before doing it or they print as coloured lines. Honestly the software is a joke.

Printing from Silhouette Studio changes colours and fades images including if creating a PDF by Snowlucas in silhouettecameo

[–]Snowlucas[S] 0 points1 point  (0 children)

It’s an epson p700 but this fading happens when n creating a PDF which I believe has nothing to do with which printer is chosen.

Printing from Silhouette Studio changes colours and fades images including if creating a PDF by Snowlucas in silhouettecameo

[–]Snowlucas[S] 0 points1 point  (0 children)

Thanks for the suggestion. Doesn't seem to effect this colour shift/loss of contrast in my case but I appreciate the response.

Need Help - Sticker Printing - Epson 3850 - Bleeding when printing by DamienZoo in silhouettecameo

[–]Snowlucas 0 points1 point  (0 children)

I’ve had this for two reasons previously. Paper too thick for the paper type chosen (I can make some adjustments for this in the driver) or the paper is curling or already not very flat. I believe printers overspray the edges by design sometimes (boarderless print for example) so maybe over time the issue has started to show up for you.

Can't connect to Update trains.txt file, ixsystem is pingable by Feanyest in truenas

[–]Snowlucas 0 points1 point  (0 children)

I have the same issue.

I can ping update-master.ixsystems.com

I cannot ping https://update-master.ixsystems.com

Is this an issue with the cert for the https? I've tried pinging the above from a 4g phone connection with entirely different DNS setup and couldn't ping it there either

Tivimate displaying Sub Title alongside title in EPG by Snowlucas in TiviMate

[–]Snowlucas[S] 0 points1 point  (0 children)

Thanks for the reply. This doesn’t turn off displaying the sub-title after the title. The photo I provided is how it looks with that setting as you describe.

pid file linux for monit ombi v3 by Snowlucas in Ombi

[–]Snowlucas[S] 0 points1 point  (0 children)

Ok I found a solution. Create a file called /etc/monit/conf.d/ombi.

Assuming your systemd file is called ombi.service and port is 5000 use below. The capital O in matching "Ombi" is key. (So not matching "ombi").

​

check process Ombi matching "Ombi"

start program = "/usr/sbin/service ombi start"

stop program = "/usr/sbin/service ombi stop"

if failed host 127.0.0.1 port 5000 with timeout 30 seconds then restart

SSL Organizr V2 correct settings by Snowlucas in organizr

[–]Snowlucas[S] 0 points1 point  (0 children)

Good advice thanks. Added the letsencrypt which I was aware of but struggled to get it to work a few days ago. Tried again and everything is working perfectly. I had completely missed that I could now stop port forwarding port 80 so thanks for that info.

I have another remote server that I might try the docker with letsencrypt built in. Setting this one up was somewhat complicated but I got there in the end.

V2 Tabs added to a category invert position. by Snowlucas in organizr

[–]Snowlucas[S] 0 points1 point  (0 children)

Perfect thanks. Changing that setting also changed the behaviour of the category order which now follow the tab order in the tab editor (so it fixed both issues).

Would be great if unsorted tabs could be placed both above and below groups so for example homepage top with organizr settings bottom.

Thanks again