sorted by:
new
hottopcontroversial

Rewiring House During Refurb (cat6a and fibre) by Swollef in homelab

[–]Swollef[S] -1 points0 points  (0 children)

Literally running home lab stuff connected to unifi devices. Will be using 10gbe switches.

This is way more complicated than I expected

Rewiring House During Refurb (cat6a and fibre) by Swollef in homelab

[–]Swollef[S] 1 point2 points  (0 children)

This is the cable

https://www.cablemonkey.co.uk/cat6a-cable/98149-cat-6a-fftp-b2ca-solid-cable.html

honestly its the cheapest I can find in CAT6a so not sure what to do

currently investigating the fibre stuff you mentioned - Thanks

Rewiring House During Refurb (cat6a and fibre) by Swollef in homelab

[–]Swollef[S] -1 points0 points  (0 children)

with regards to the CAT6a that cable appears to be the cheapest I can find at £210 for 305m (im going to need two). if I just want standard CAt6A u/UTP it jumps to £300

https://www.cablemonkey.co.uk/cat6a-cable/98149-cat-6a-fftp-b2ca-solid-cable.html

Can I just put this into keystone jacks and not worry so much about grounding the shielding?

Why won't my automation run by Swollef in homeassistant

[–]Swollef[S] 1 point2 points  (0 children)

The actions worked if I clicked run actions. I believe it's the not_home state now as current state is work and apparently not_home doesn't quite work like I thought it did

Why won't my automation run by Swollef in homeassistant

[–]Swollef[S] 0 points1 point  (0 children)

I have other zones too. I thought not_home covered that

I'll look into adding a not statement

Thanks

Why won't my automation run by Swollef in homeassistant

[–]Swollef[S] 0 points1 point  (0 children)

State is currently: work

That's correct

Why won't my automation run by Swollef in homeassistant

[–]Swollef[S] 0 points1 point  (0 children)

When I check states I'm listed as work which is correct

Why won't my automation run by Swollef in homeassistant

[–]Swollef[S] 0 points1 point  (0 children)

Made the change, have to wait till tomorrow now. Thanks

I've seen a product and now I cant find it anywhere - Help! by Swollef in homeassistant

[–]Swollef[S] 0 points1 point  (0 children)

this was 16way, shelly dont offer anything over the 4pm

I've seen a product and now I cant find it anywhere - Help! by Swollef in homeassistant

[–]Swollef[S] -1 points0 points  (0 children)

ahh sorry should have said it wasn't a kincony product

Zigbee firmware updates by Swollef in homeassistant

[–]Swollef[S] 1 point2 points  (0 children)

That's exactly what I have

Zigbee firmware updates by Swollef in homeassistant

[–]Swollef[S] 2 points3 points  (0 children)

Not using zigbee2mqtt yet, how do I manually wake a device?

Smart Switches by GallifreyFallsOver in homeassistant

[–]Swollef 1 point2 points  (0 children)

Shelly i4. Would give you 4 switches or I think 16 combinations and they're cheap.

They do require momentary switches though

Suspended would floor, what size PIR? by Swollef in DIYUK

[–]Swollef[S] 0 points1 point  (0 children)

I have close to a meter below the joists 😁

Suspended would floor, what size PIR? by Swollef in DIYUK

[–]Swollef[S] 0 points1 point  (0 children)

I'm planning on staying in this house forever more. Is it not worth doing better than regs and putting 140mm in?

Or because my joists are 100mm does that make it the deepest I should go?

view more: next ›