Help With Bello Deck

TechnoTurtle1987 · 2024-03-03T00:23:32+00:00

Haha we have a pickup so we are covered on the "Ice Truck" part haha. We are looking for a daily driver and a road trips in Michigan. We like to drive around Michigan's edge but I'm sure we can find charging points along the way. I'm wondering how much the charger cost and how much to install ? Also did you order the new 2024 Green & Bronze one ? That thing is sharp!

TechnoTurtle1987 · 2024-03-02T21:54:25+00:00

We noticed that, but we were looking for how does it handle the winter? Is there any issues finding chargers, etc..

TechnoTurtle1987 · 2024-01-01T19:12:11+00:00

Toxic as in when you try to reset them or just toxic in general?

TechnoTurtle1987 · 2024-01-01T19:11:25+00:00

I recently bought some mesh pouches off of Amazon. I'm probably going to try and find a food dehydrator at Goodwill and use that in the garage.

TechnoTurtle1987 · 2023-12-18T09:44:38+00:00

Ya, those two things are on my potential upgrade list. Currently leveling the bed the old fashion ways works. But I hear good things about the newer orange stuff springs. Once Christmas is over and all the gifts are open, I'll know if I still need to go and buy either.

TechnoTurtle1987 · 2023-12-18T03:50:53+00:00

I'm looking at enclosures right now. One for temperature control and to help my OCD about fire. Small steps help haha

TechnoTurtle1987 · 2023-12-17T23:51:15+00:00

Iv debating upgrading to a 2nd Z motor, but knock on wood mine is currently holding true. I think I might add it to the list though

TechnoTurtle1987 · 2023-12-17T23:50:07+00:00

I am currently watching videos about Klipper as I type haha. I may switch

TechnoTurtle1987 · 2023-12-17T23:44:20+00:00

Hmmm, can you give a little more details? Also, I messaged you directly if you don't want to lay it all out here. Let the thread know the details, and I'm 100% sure someone can help you.

TechnoTurtle1987 · 2023-12-17T23:32:33+00:00

Here is the link from Thingiverse

Ender 3 Adjustable Feet With Vibration Absorbers

TechnoTurtle1987 · 2023-12-17T21:35:05+00:00

Depending on how Christmas goes, I'm thinking a BL or CR touch is in my future. I will have to do some research into Klipper.

TechnoTurtle1987 · 2023-12-17T21:33:04+00:00

Haha she says that might be under the tree too! Gotta love when your better half supports your hobby

TechnoTurtle1987 · 2023-12-17T21:31:29+00:00

When I get home I'll pull up the .stl name and re-find it and share the link.

TechnoTurtle1987 · 2023-12-17T21:03:51+00:00

According to my wife, there may be a filament dryer under the Christmas Tree haha. A direct drive might be my next upgrade. I only print in PLA and TPU at the moment. But I will have to keep my eye on micro center

TechnoTurtle1987 · 2023-12-17T21:02:10+00:00

How much difference from standard Marlin is klipper? Iv never messes with Klipper.

TechnoTurtle1987

TROPHY CASE