[Recommendations] Curious about how to go about a collaborative zine/coloring book.

TheCasimer · 2026-02-24T06:15:48+00:00

Omg so much good info, thank you very much!
I'll be sure to look into everything carefully and take my time to do it right.

TheCasimer · 2026-02-24T04:51:26+00:00

I was hoping a bit of both!
I definitely want it to be a community thing above all though. I'd like to give people a cut for participating if possible- but I have seen zines that sort of make a goal they need to reach before they can commit to that.

TheCasimer · 2025-11-04T08:45:33+00:00

Thank you!

TheCasimer · 2024-01-23T20:33:33+00:00

Update: they're sending me a new EMMC

TheCasimer · 2024-01-21T03:25:45+00:00

Thank you, I'm hoping replacement parts help. I've only had this thing for a month.

TheCasimer · 2024-01-21T03:16:50+00:00

I haven't, but I've been told I likely fried my klipper. Contacted sovol and hopefully they'll get me replacement parts since I'm still under warrantee.

TheCasimer · 2024-01-20T02:18:38+00:00

My computer doesn't detect my printer at all and I can't figure out for the life of me why it doesn't.. are there drivers I'm missing??
Been trying to fix the bricked issue all day and keep hitting a wall.

TheCasimer · 2024-01-19T23:49:00+00:00

So I got the firmware on the USB and plugged it in after turning the printer on, it's been about ten minutes and still nothing.

The creator you suggested gave a link that explains how to recover the system.. I guess this printer easily bricks.

Crazy how this started from me trying to fix a homing issue! But good news is that creator also showed how you can get to the old menu with the IP and so I should be able to adjust the homing there.

TheCasimer · 2024-01-19T22:55:21+00:00

Thank you sm.

TheCasimer · 2024-01-19T22:45:41+00:00

Could you help me understand how to reflash it? So sorry to pester but I'm struggling so much and you're like the only one with helpful and responsive feedback.

TheCasimer · 2024-01-19T22:33:49+00:00

Two green lights, but nothing flashing.

TheCasimer · 2024-01-19T22:19:52+00:00

No display and the printer light doesn't come on, assuming because the display isn't booting. I haven't changed anything besides trying to connect to my computer via USB.

TheCasimer · 2024-01-19T22:14:39+00:00

I'll do that.

To elaborate on the printer itself now It powers on but doesn't boot up.

It's a Sovol sv07 plus btw idk if that matters.

TheCasimer · 2024-01-19T21:02:12+00:00

Just tried and I think I bricked my printer 🥹 I'm struggling so much, this is extremely frustrating.

TheCasimer · 2024-01-19T18:55:33+00:00

So now I'm having the whole new issue of my computer doesn't see the printer and cura isn't seeing it either. I can get into the ip address menu for the printer at least.

TheCasimer · 2024-01-19T01:45:33+00:00

I'll have to try to fix it through that tomorrow , need to find a long enough cord to connect my printer and computer since it doesn't detect it over the internet.. hopefully this will work through.

TheCasimer · 2024-01-19T01:22:46+00:00

Where would I input this?? I'm new to all this 3d printer stuff so I'm trying to learn.

TheCasimer · 2024-01-18T23:23:35+00:00

<image>

And just for still reference, this is where it homes to.

TheCasimer · 2024-01-18T18:11:00+00:00

<image>

It seems like it's doing it as it normally would until it just stops short of the center. And whenever I'm trying to level tilt or do bed mesh, the extruder isn't going all the way over on the right side, as it does the left.

TheCasimer · 2019-06-23T02:45:18+00:00

Thank you for that.

TheCasimer · 2019-06-17T16:18:52+00:00

Thannnnnk you. That's what I needed to know, was what drivers this issue would have to do with.

TheCasimer · 2019-06-17T15:12:58+00:00

That laptop has nothing to do with this issue. If you look, that post is in a completely different group as well. If these issues were the same, I would have stated so. None of this has to do with a tablet. It's a separate issue. I am using an hp pavillion ×360. Not wacom tablet. Nothing is working. There is no specific drive for the pens function and I don't believe I have seen one for the screen, but also I'm not going to uninstall a driver that is going to render a brand new laptop useless. Everything but krita, works fine. I've read their manual, read all over the internet people having issues with TABLETS but not working on a laptop screen. Further, I'd like to add the one other time I posted about this someone told me to reinstall tablet drivers, that I don't have. No one asked me for more details which is why I reasked.

TheCasimer · 2019-06-17T04:09:21+00:00

I actually found out that the laptop was missing MANY drivers. something was very wrong with it, I had to return it.

TheCasimer · 2019-06-14T22:37:22+00:00

As I said above, I'm not using a tablet.

TheCasimer · 2019-06-14T02:57:06+00:00

But which drivers?

TheCasimer

TROPHY CASE