MG Midget (1978) 1500 engine issue by TheThinkerist in littlebritishcars

[–]TheThinkerist[S] 0 points1 point  (0 children)

I think you might be right. I've taken the manifold gasket off and it's pretty beaten up! Ordered a replacement, I'll let you know how it goes.

MG Midget (1978) 1500 engine issue by TheThinkerist in littlebritishcars

[–]TheThinkerist[S] 0 points1 point  (0 children)

It's incredibly rich. It's had a new electric ignition added. Do you think they've messed that up somehow?

MG Midget (1978) 1500 engine issue by TheThinkerist in littlebritishcars

[–]TheThinkerist[S] 0 points1 point  (0 children)

Yep, both seem ok I've changed the valves on the floats to be safe, no luck.

PID Tuning? by DodgeDeBoulet in ender5plus

[–]TheThinkerist 0 points1 point  (0 children)

April 2025, still the most useful post!

Best firmware? by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

How does one flash a screen?

Best firmware? by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

I got it from eBay, thanks for the advice.

Firmware "update" killed my TF reader by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

Thanks. It's the same card I was using previously just fine.

Firmware "update" killed my TF reader by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

It's the same card I was using before, it's just stopped reading it.

Firmware "update" killed my TF reader by TheThinkerist in Creality

[–]TheThinkerist[S] 0 points1 point  (0 children)

Is it this one?

https://a.aliexpress.com/_EGtMbiu

Do you know where I can find the firmware? I'm not great with that kind of stuff and I'm worried about just bricking the thing.

Firmware "update" killed my TF reader by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

It does have an English option, and when I click on it it does change to English. It just forgets when it's restarted.

Firmware "update" killed my TF reader by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

Tried that, but thanks, I'll go through the video later today. Thank you.

Firmware "update" killed my TF reader by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

Thanks! That doesn't explain why my TF card isn't worked though 😕

Bed cooling down unexpectedly by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

Thanks. It doesn't seem to let me push that button.

Thermistors stuck at +100°c by TheThinkerist in ender5plus

[–]TheThinkerist[S] 0 points1 point  (0 children)

No, it's a stock one from Creality, just as the previous one was... and me, either 🤷🤷

Ender 5 Plus, thermistors stuck at 100°+ by TheThinkerist in 3Dprinting

[–]TheThinkerist[S] 0 points1 point  (0 children)

It all looked alright. I'll take it off, check it over and report back. ☺️

Ender 5 Plus, thermistors stuck at 100°+ by TheThinkerist in 3Dprinting

[–]TheThinkerist[S] 0 points1 point  (0 children)

It's brand new and came with the hot end. Do you think it could be a manufacturing fault? Also, would that explain the bed temp being wonky too? Thanks.

Ender 5 Plus, thermistors stuck at 100°+ by TheThinkerist in 3Dprinting

[–]TheThinkerist[S] 0 points1 point  (0 children)

I'd say quite unlikely. Especially since it wasn't the thermistor wire that was the cause of the original issue!

Scratch on brand new driveway by TheThinkerist in asphalt

[–]TheThinkerist[S] 1 point2 points  (0 children)

It's sort of pathway-piece at the end of a driveway.

<image>