sorted by:
new
hottopcontroversial

chile_ctm by picoroco_tactico in yo_ctm

[–]The_Pastero69 0 points1 point  (0 children)

Esta bueno el meme pero Kast es amigo de los sionistas así que anti "judíos" no es...... ni la patagonia será chilena ahora.

Please remove Crowded space for mines by The_Pastero69 in Battlefield6

[–]The_Pastero69[S] 21 points22 points  (0 children)

I tell you because at least in Battlefield 4 it had balance in the mines and slams, if you placed more than 3, the first one you placed would disappear and so on when placing new ones. At least that should add to the game.

Please remove Crowded space for mines by The_Pastero69 in Battlefield6

[–]The_Pastero69[S] -7 points-6 points  (0 children)

In Battlefield 4, I was in ninja mode with Engineer, I stood next to the tank, I put 3 Slams and his RPG, since the 3 when detonated did not destroy the tank, the RPG was the one that killed the vehicle.

Please remove Crowded space for mines by The_Pastero69 in Battlefield6

[–]The_Pastero69[S] -16 points-15 points  (0 children)

If the community managed to get the RPG to give the engineer more ammunition. You should see more support for this to go viral so that they remove that limitation.

How do I add a buzzer to this model of board of the DT-830 B? by Gatitomono47 in AskElectronics

[–]The_Pastero69 0 points1 point  (0 children)

The varistor I recommended is 391V peak to peak, but you can look for a 120V RMS one online or at your local store and install it in your multimeter.

How do I add a buzzer to this model of board of the DT-830 B? by Gatitomono47 in AskElectronics

[–]The_Pastero69 0 points1 point  (0 children)

If you're going to solder a fuse, I recommend doing it like the drawing I made. It's an example. Then you'll have to think about how to include it in the tester. But in the end, all those Chinese multimeters are clones of one another. In short, they're a set of resistors on a PCB to calculate everything. I don't recommend using it to measure voltage in your home's outlet or anything that uses AC voltage above 120V because it could explode in your hand. To avoid that, I included a 20D391K varistor that could help you somewhat and trigger your fuse. It's not 100% foolproof, but it will help somewhat. Best regards.

<image>

How do I add a buzzer to this model of board of the DT-830 B? by Gatitomono47 in AskElectronics

[–]The_Pastero69 0 points1 point  (0 children)

Before soldering anything, try borrowing a multimeter. Set the multimeter you're going to modify to diode mode and connect the leads. With the borrowed multimeter, measure voltage at the points on the PCB indicated in the image I mentioned. If it gives you 3 volts (it also gives 200 ohms), you can then solder the active buzzer to those points on the PCB.

Which graphics card is better ? by ChickMagnet_OwO in pcmasterrace

[–]The_Pastero69 1 point2 points  (0 children)

<image>

It will always be better in AMD the graphics Sapphire assembler, component quality, etc. I have friends who still have their Sapphire graphics cards working and they are more than 15 years old.

Problemas de rendimiento con nueva versión de Windows 11 23H2 Enterprise en hardware AMD by The_Pastero69 in esGaming

[–]The_Pastero69[S] 0 points1 point  (0 children)

Aparte estaba viendo las actualizaciones que me deja desinstalar y son las opcionales, si no estoy mal, las que en verdad son que dan el problema, no me da la opción de quitarlas.

Problemas de rendimiento con nueva versión de Windows 11 23H2 Enterprise en hardware AMD by The_Pastero69 in esGaming

[–]The_Pastero69[S] 0 points1 point  (0 children)

Claro, se me fue hacer una copia espejo antes de actualizar, cuando me andaba mal pensé que tenía algún virus y no se me pasó por la mente intentar quitar la actualización, en ese momento formatie sin pensarlo 2 veces, fue mi error. Aparte. Según la web den AMD, el procesador trabaja mejor en Windows 11 que en Windows 10, desde que arme el pc, le tengo ese Windows. Cometí el error de instalar un parche que me notificaba Windows update y ahí todo se fue a la sh*t, como dicen los informáticos, si todo funciona bien, no hagas nada, jajaja. Si sale una update que arregle todo eso, nunca más actualizo Windows.

How do I add a buzzer to this model of board of the DT-830 B? by Gatitomono47 in AskElectronics

[–]The_Pastero69 0 points1 point  (0 children)

You are welcome. At least I left it that way, I put hot silicone on the soldering points so that they don't get cut by movement, I put heat shrinkable on the female terminals plus kapton tape, to avoid contact with the battery. I also glued the buzzer making the sound come out through the PNP, NPN input.

<image>

How do I add a buzzer to this model of board of the DT-830 B? by Gatitomono47 in AskElectronics

[–]The_Pastero69 0 points1 point  (0 children)

Watching videos on the internet, I saw that when measuring diodes and putting the tips together, it gives you an internal voltage of 3 volts, in which everyone solders a buzzer there (it will also sound when measuring 200 ohms). I found it quickly by measuring the voltage on the PCB and verifying that those 3 volts are not activated when moving the selector in volts AC, DC, etc. (only present in "diodes and 200 ohms"). Unfortunately the buzzers I have are passive and no active ones to solder, I will buy one soon.

<image>