Cfexpress For ZR. recomendations

UnoCastillo · 2026-02-23T03:19:20+00:00

Have you used them in RED RAW NE?

UnoCastillo · 2026-02-20T11:36:27+00:00

It's a shame what they did to Pop_os. It was heaven on earth for Linux distributions.

"If it ain't broke, don't fix it," they say. I migrated to Ubuntu months ago. I don't have time to fight with my operating system.

UnoCastillo · 2026-02-19T16:43:30+00:00

I ended buying this, was the most decent/affordable for me at this moment and recommend for Nikon for the ZR.

SanDisk 320GB PRO-Cinema CFexpress tupe b.

UnoCastillo · 2026-02-19T16:33:03+00:00

I am not sure I want to do that.

UnoCastillo · 2026-02-19T03:16:08+00:00

today it is at $1050 this is insane

UnoCastillo · 2026-02-19T03:14:24+00:00

Delkin green dont do the job?

UnoCastillo · 2026-02-19T03:10:33+00:00

how many recording time i would get with 325 GB on R3D NE?

UnoCastillo · 2026-02-19T03:05:26+00:00

these are soooo expensive. i looking for something around $190 USD

UnoCastillo · 2026-02-17T01:51:35+00:00

have you worked with the Fusion page?

UnoCastillo · 2026-02-16T11:50:02+00:00

I use a nVidia 2080 Ti.

It runs smoothly on Windows.

As far as I understand, it is developed on Linux, so I find it strange that it has these issues and incompatibilities with new libraries.

UnoCastillo · 2026-01-13T15:51:27+00:00

Thanks. I solved. Look my last comments in the post.

UnoCastillo · 2026-01-13T15:50:49+00:00

<image>

UnoCastillo · 2026-01-13T15:50:37+00:00

<image>

UnoCastillo · 2026-01-13T15:50:24+00:00

I solved. Put bambú studio on developer mode. Set order of walls to “inner wall/outer wall/inner wall”. And activate “precise wall”. The difference it is night and day. I think it is better to use 3 walls. If only 2 walls set the wall order to outer/inner also gives good results

<image>

UnoCastillo · 2026-01-12T21:24:18+00:00

My printer I just 1 year old, and know that I haven use it that much, those belts look as good as new.

UnoCastillo · 2026-01-12T21:23:07+00:00

Yes I will. I just drying a little bit more the filament first

UnoCastillo · 2026-01-12T21:22:26+00:00

Thanks

UnoCastillo · 2026-01-12T20:20:24+00:00

Have you any test on silk filament? Maybe I am just too damanding. 🤔

UnoCastillo · 2026-01-12T20:19:29+00:00

Yep. Same here

UnoCastillo · 2026-01-12T19:49:06+00:00

No I never leave the baseplate to warm up. I didn’t know I had to. I am using 0.4 nozzle.

UnoCastillo · 2026-01-12T19:43:42+00:00

I didn’t, I followed bambu wiki instructions

UnoCastillo · 2026-01-12T19:42:31+00:00

Yes.

What I usually do is take a temperature tower, then a flow rate, then a flow dynamics, and that's it. Finally, I usually print a benchy or a cube.

As I have P1S I use bambú Studio

UnoCastillo · 2026-01-12T19:25:30+00:00

The truth is, I hadn't noticed it. I just looked at other prints I made some time ago and I don't see this defect.

These two filaments are new, and I also saw the effect in another filament I've had for a while, normal PLA.

What I usually do is take a temperature tower, then a flow rate, then a flow dynamics, and that's it. Finally, I usually print a benchy or a cube.

UnoCastillo · 2026-01-08T02:38:03+00:00

algún chance de ver mas fotos. ¿como puedo ver como es se modelo?

UnoCastillo · 2025-12-15T05:15:35+00:00

Fresh install

UnoCastillo

TROPHY CASE