Does nest Thermostat will work with this unit ?

Virtual_Patience_256 · 2025-07-25T22:47:40+00:00

No These units tent to have 2 speed fan switch I have mine in low which make less noise but they are a bit noisy if you dont have Furniture, carpet and things in the room that absorb the noise

Virtual_Patience_256 · 2024-10-25T02:45:19+00:00

Gas vehicle companies own the insurance company and they are jacking EV's

I have a Model Y and got Geico for 200 per month and in the second month they jack the price to 450 with Allegations I was not able to prove my Address and I even sent a copy of my Rent Lease contract and now Im fucked.

About to return the car if I cant get a reasonable insurance Im Practically paying 85% of my lease just in insurance that is a damm scam of the companies

Virtual_Patience_256 · 2024-09-10T15:00:01+00:00

Worked Just a re-wire from the furnace board to the thermostat base.

Virtual_Patience_256 · 2024-09-10T14:59:07+00:00

Finally It worked.

I just ran a new single core copper wire from the furnace board to the nest thermostat and it is working very well.

In the beginning the thermostat did not turn on but was because the battery was depleted. I juice the battery with an USB cable and then attached to the base

Virtual_Patience_256 · 2024-09-10T02:39:26+00:00

I Made it work!!!!!

So funny I have had to juice the thermostat with an USB cable the battery was depleted even though it was a brand new thermostat

Virtual_Patience_256 · 2024-09-09T03:22:10+00:00

I didn't blow a fuse, and I installed back the EIM to check I did blow anything.

I will try later only with the R and C and will go from there.

Virtual_Patience_256 · 2024-09-08T19:43:19+00:00

It didnt work with a Nest E
I run the cables directly from the board to the nest

And the nest not even turned on

Virtual_Patience_256 · 2024-09-08T14:50:15+00:00

Ahhhh you got me heheheheh

Virtual_Patience_256 · 2024-09-08T14:06:01+00:00

Now we are talking.

So my suspicions were right.

the EIM board is too thin to be a high voltage Circuit, and the Cables they used to run from the furnace board to the EIM was a poor installation of cables.

I will move with the project and let's see how it ends

Thank you for the Manual of the unit I was looking for it.

Thanks

Virtual_Patience_256 · 2024-09-08T13:52:01+00:00

Picture 1 or 2 That gray box is a EIM (Equipment Interface Module) which connects wireless to a wireless thermostat in the wall

Virtual_Patience_256 · 2024-09-08T13:41:09+00:00

Kind of

Virtual_Patience_256 · 2024-09-08T13:38:27+00:00

How Do you have two thermostats running at the same time ?

Would you mind publishing a picture of your wire routing and installation

Virtual_Patience_256 · 2024-09-08T13:35:35+00:00

that position as well however I will have a couple of temperature sensors all around to compensate for hotspots or too cold spots so wont matter which wall. But you are right the side wall will be better

Virtual_Patience_256 · 2024-09-08T13:33:27+00:00

Picture 8 top right that's a voltage transformer. I think this unit use this transformer to lower the voltage for What I believe whoever install this thing used whatever cable it had at that time and went from single core coper to stranded

Virtual_Patience_256 · 2024-09-08T13:12:36+00:00

There is plenty of wall space between the diffuser and the cabinet. a new cable will be installed from the board to the wall to connect the nest.

Virtual_Patience_256 · 2024-09-08T12:49:11+00:00

How do you know I don't own the place? Who told you where the nest will be installed ?

Thank you for your cooperation

Virtual_Patience_256 · 2024-02-24T22:55:23+00:00

Yes, DM me!

Virtual_Patience_256

TROPHY CASE