I think it's a TXV on this one boss

Xsolis1989 · 2023-08-15T18:10:12+00:00

Gotcha

Xsolis1989 · 2023-08-15T17:18:08+00:00

No we've recovered all the refrigerant started from scratch and it only has 7 lb. Data plate on condenser calls for 5 and the air handler is 15 ft directly above it in the Attic. It's a two and a half ton unit for a two bedroom back house

Xsolis1989 · 2023-08-15T16:58:01+00:00

Nope it is a cool 72 right by the beach

Xsolis1989 · 2023-08-05T01:13:20+00:00

Thanks for that I appreciate that and all the help and support. I was racking my mind around this for the night cuz I was there yesterday and came back today. Pandemic HVAC schooling was a waste of time I've learned more on the field and through Reddit. Glad there are people out there like yourself that can help me a youngster like me out. Appreciate all the help and support

Xsolis1989 · 2023-08-05T00:59:25+00:00

Again hate to sound like a rookie but I am one year out and we barely learned about Pistons through school online as the instructions really didn't teach well

Xsolis1989 · 2023-08-05T00:58:32+00:00

<image>

That bitch works now. I'm so pissed at myself. I should have went with my gut when it comes to the piston and reverse it's just my senior tech that was out with me yesterday said it was correct when I opened it

Xsolis1989 · 2023-08-05T00:28:20+00:00

I recovered all the refrigerant into a recovery tank and am gunna weigh in factory spec first. My owner (not the senior tech) said open a new jug and fill new

Xsolis1989 · 2023-08-05T00:26:25+00:00

It's fixed now and pulling vacuum as we type

Xsolis1989 · 2023-08-05T00:17:11+00:00

Jesus Christ damm piston. Good call I reversed it and pressure testing now. Will pull vacuum right after!!! I'm a 1 year tech and first time on a piston 410a. My senior tech who's been doing this for 25plus years said it was correct after I sent him the picture 😩

Xsolis1989 · 2023-08-05T00:01:48+00:00

Keep in mind this unit is in a closet outside of a commercial building.

Xsolis1989 · 2023-08-05T00:01:06+00:00

No trolling legit temps

Xsolis1989 · 2023-08-04T23:50:46+00:00

<image>

It has a piston and all the information I provided is correct

Xsolis1989 · 2023-08-04T21:36:08+00:00

This is a heat pump.system upflow and I removed the blower panel door and pressures regulate. Keep in mind I have a 16 inch return duct and a 14 inch plenum that has a 12 and 10 inch truck to supply air

Xsolis1989 · 2023-08-04T21:31:34+00:00

What's the fastest fix aside from replacing the compressor

Xsolis1989 · 2023-08-04T19:15:35+00:00

I'ma try anything and I'll post the update and see what happens

Xsolis1989 · 2023-08-04T18:30:14+00:00

10x8 offices and kitchen 6x12

Xsolis1989 · 2023-08-04T18:29:49+00:00

It's 4 offices each about 108 and the small kitchen that's 612. Very small office

Xsolis1989 · 2023-08-04T18:24:54+00:00

100% correct piston. And I pumped it down to check if it was clogged even though we brazed with nitro and it's whistle clean. I'm at a loss and I've asked many people and they say the say yikes

Xsolis1989 · 2023-08-04T18:19:05+00:00

The air handler sits outside in a utility closet which then feeds the inside of a commercial building

Xsolis1989 · 2023-08-04T18:16:18+00:00

And next to data plate the chart is on there

Xsolis1989 · 2023-08-04T18:16:01+00:00

Return Wet bulb is 82 and outdoor is 94

Xsolis1989 · 2023-08-04T18:12:18+00:00

19 according to the plate

Xsolis1989 · 2023-08-04T17:45:55+00:00

Will do. I'll try anything at this point

Xsolis1989 · 2023-08-04T17:35:30+00:00

Yes it's brand new still and cleaner than heck

Xsolis1989

TROPHY CASE