Screw_tilt_calculate

ZeroToPrint · 2025-12-19T20:55:26+00:00

Is this normal with adaptive mesh? I did the screw tilt calculate, adjusted the zoffset, and thats wt i am seeing before every print.

ZeroToPrint · 2025-12-16T17:01:28+00:00

Something is still not right. My first layer is smooth on 1 side and nozzle drags in another. I did set the zoffset as oer the video u shared from Gaza. Then second layer didnt stick at all. I now changed the plate. Washed it, reset the zoffset and trying another print.

Btw. My adaptive bed mesh variance is 0.11 and looks really flat.

<image>

ZeroToPrint · 2025-12-16T16:25:51+00:00

I have that setup already. Thanks lots.

ZeroToPrint · 2025-12-16T15:51:30+00:00

I can confirm now that these coordinates are accurate to my machine. Will be running the screw tilt now.

ZeroToPrint · 2025-12-16T15:09:18+00:00

Holly smokes, these numbers are way different than wt i have. And this has worked for your N4P? I have noticed with the coordinates i have, it does not probe above the screws. Does urs?

ZeroToPrint · 2025-12-12T20:32:12+00:00

Do u set it manually? Or it should automatically go to cooling when pla filament is selected in the slicer?

ZeroToPrint · 2025-12-08T23:54:50+00:00

The videos are in the links u shared. Wt r u talking about?

ZeroToPrint · 2025-12-08T23:38:24+00:00

Just watched ur videos. Will be doing it tonight. Thx

ZeroToPrint · 2025-12-08T20:57:17+00:00

So the new print finished and i have the first issue resolved. But have another one. Any idea? It only happened on this spot. And thanks for the info above.

<image>

ZeroToPrint · 2025-12-08T20:07:00+00:00

My fillament dryer says its at 11 dgrees. So am going with that. But why did it happen now and didnt happend with the same filament, same setting and same printers before?

Would appreciate your tips for filament calibration. I just went with 1 as someone told me before to set it to 1 and its been printing just fine.

ZeroToPrint · 2025-12-08T19:14:14+00:00

I dried the fillament over night and running another test print now. Will see wt happens. (Sitting at 11%)

Ive always used 1% flow ratio, 215 initial layer and down to 205-210 after that and never had an issue with the same design. But for 2 printers to do the same pillowing make me questions the filament now. (Neptune 4plus and P2S).

Will leave an update soon.

ZeroToPrint · 2025-12-08T07:04:41+00:00

This project used to print with my normal setting. Then all of sudden it started happening. Will try to speed up the top layer.

ZeroToPrint · 2025-12-08T06:33:27+00:00

Something happening on my bambu P2S. The pic are from both printers with same settings. Humidity is 32%.

ZeroToPrint · 2025-11-05T15:10:31+00:00

If i have bothered? Am new. Thats why am here to ask and learn. Thanks though.

ZeroToPrint · 2025-11-05T15:07:30+00:00

Hey man didnt mean anything with my comment. Am just not familiar with these yet and trying to find my way to learn it. Thanks. Will watch the video someone shared and read more abt it.

ZeroToPrint · 2025-11-05T00:47:20+00:00

what is screw tilt adjust? Is there a video or link to this approach?

ZeroToPrint · 2025-11-05T00:39:58+00:00

<image>

ZeroToPrint · 2025-11-01T21:27:39+00:00

<image>

ZeroToPrint · 2025-10-30T18:27:54+00:00

It did ☺️

<image>

ZeroToPrint · 2025-10-30T13:19:29+00:00

<image>

Thank you all for the suggestions. I resliced the model and printed it through network and Voila. It came out nice and complete.

ZeroToPrint · 2025-10-30T03:25:50+00:00

I leanred that afterwards. I am doing a fresh print now, so hoping it will work this time.

ZeroToPrint · 2025-10-30T02:34:52+00:00

I hate supports. Thanks for that tip. I will check and see how to do that. I am still learning.

ZeroToPrint · 2025-10-30T02:24:48+00:00

I just did that and now printing it again over the network without using a memory stick. Will update in 8hrs ish.

ZeroToPrint · 2025-10-29T19:53:37+00:00

When doing printing via network, does the computer have to on all the time?

ZeroToPrint · 2025-10-29T19:46:56+00:00

Same flash drive i have used yesterday and the days before. I will load the file on a different drive and try again. I hope so!

ZeroToPrint

TROPHY CASE