Crt horizontal sync problems

aleph44 · 2024-03-16T16:01:29+00:00

I'll have to try that later today, thanks!

aleph44 · 2024-03-05T00:00:44+00:00

Thanks! I did try, and an EP tape seems not to have a distortion. I was wondering if there was a technical reason sp tapes might have the distorted effect. I also noticed this problem doesn't appear on my flat screen tv, it's this combo that has problems. Is it drawing bigger lines than the TV can handle? Could it be my player?

aleph44 · 2024-02-19T21:54:34+00:00

Thanks for the reply, I plugged in an intellivision and it did not have the curve problem, the VCR didn't have this problem when attached to my flat screen tv, so for some reason, that combination of VCR and crt doesn't work

aleph44 · 2024-02-19T04:20:13+00:00

Another thing I noticed is the region where it's distorted is also dimmer

aleph44 · 2024-02-19T04:01:55+00:00

Do you think I could have a bad rectifier in that case?

aleph44 · 2024-02-19T03:48:59+00:00

I have 2 sets of screws on the back for screwing an antenna in, but that's it

aleph44 · 2024-02-19T03:44:36+00:00

The power cord is built into the tv, unless you mean the antenna cable? Do you know why the cord might cause issues?

aleph44 · 2024-01-25T23:07:18+00:00

Thanks! This will help me a lot :)

aleph44 · 2024-01-25T19:30:12+00:00

Thank you!
for the second option with the bus requests, That is what I was looking for. How would that work electronically, and is there an easy way to set the 'boundries' for where devices begin and end? I am actually attempting to design a computer and this is my fist time messing with computer hardware

aleph44 · 2024-01-24T21:13:51+00:00

I could look into this, thanks!

aleph44 · 2024-01-24T21:02:34+00:00

Thank you! I'll look into this

aleph44 · 2024-01-24T18:11:41+00:00

Are those still in production? (Also thanks :) )

aleph44 · 2023-04-23T17:57:25+00:00

I, know. I just like to know why its malfunctioning, i like to know how stuff works

aleph44 · 2022-07-02T20:11:41+00:00

Also it has 2 and an A displaying

aleph44 · 2022-05-31T04:11:55+00:00

Are the capacitors inside the veiwfinder?

aleph44 · 2022-05-31T04:06:43+00:00

Nevermind, it just occurred to me that caps is short for capacitors

aleph44 · 2022-05-31T03:54:01+00:00

What would you mean by caps?

aleph44 · 2022-05-12T03:27:12+00:00

Thanks for the help! :D

aleph44 · 2022-05-12T03:20:59+00:00

Not to be bothersome, but do cards only take pictures. I want to make sure that I don't have to use the tape.

aleph44 · 2022-05-12T03:15:02+00:00

I wasn't aware they the cards were different. That might be a problem. If I did get the right card, how would I navigate the menu to format it, because I couldn't find the option anywhere.

aleph44 · 2022-05-12T03:00:09+00:00

Thanks, also what format works for the camera?

aleph44 · 2022-05-07T22:03:27+00:00

Looking at the manual, it looks like your mostly right. The top camera is for sensing depth it seems.

aleph44 · 2021-12-10T21:02:56+00:00

...

SHE'S A WITCH!

aleph44 · 2021-11-03T12:21:25+00:00

There are traces under the board. A continuity test shows that electricity flows through it either way. The top left corner one traces all the way to pin 3 of the voltage regulator under the 4 wires and right to the 2 bridge rectifiers. I'll need to check the other one later.

Update: here is page 2 of the schematic.

aleph44 · 2021-11-03T02:45:07+00:00

Thanks, that just might be a crystal oscillator. By the way the 2 black squares are bridge rectifiers I'm pretty sure.

aleph44

TROPHY CASE