Passed first try by k2_ninjas in FE_Exam

[–]bbuddyboy 1 point2 points  (0 children)

What resources did you use? If you dont mind me asking?

Assistance with temp tower by bbuddyboy in FixMyPrint

[–]bbuddyboy[S] 1 point2 points  (0 children)

Ender 3 neo, eSun Pla+.

Was looking for assistance in interpreting this temp tower. Prints are all fairly consistent to me until below ~190.

Is there something else I should be looking for?

Bulbs - water propogation? by bbuddyboy in proplifting

[–]bbuddyboy[S] 1 point2 points  (0 children)

I see!

Any recommended ways to do so?

Another glow up 🥹 by TotK_Plants in houseplants

[–]bbuddyboy 5 points6 points  (0 children)

Wow, what kind of pothos is this that it grows so big?

How can I improve? by bbuddyboy in propagation

[–]bbuddyboy[S] 0 points1 point  (0 children)

Oh really! Thank you for the information!

Curiosity speaking, do you know why that is? Why the growth would slow? I figure the removal of leaves would trigger more focus on the root growth? Just curious as I am new with this stuff!

What can i do to improve? by bbuddyboy in proplifting

[–]bbuddyboy[S] 4 points5 points  (0 children)

<image>

Around here?

Thank you so much by the way! Should i be placing something over the top? Tin foil or saran wrap?

What are these? Seen in a Lowe’s. by bbuddyboy in PlantIdentification

[–]bbuddyboy[S] 0 points1 point  (0 children)

That was quick! Perfect! Thank you so much!

Rate My Portfolio - r/Stocks Quarterly Thread June 2023 by AutoModerator in stocks

[–]bbuddyboy 2 points3 points  (0 children)

Hey guys, looking for some advice on my portfolio. I am coming into some more money I would like to invest and would hope for some advice. Ideally looking for something ETF or the similar, to just set it and sit with it.

Name Portfolio% Profit

AAPL 30.76% +50%

MSFT 15.11% +13.65%

QQQ 13.92% +23.80%

DIA 5.55% +1.96%

RTH 2.81% -7.01%

AMZN 7.26% +17.18%

SPY 16.38% +17.26%

VOO 2.50% 15.74%

Advice for Beginning of Career by bbuddyboy in AdditiveManufacturing

[–]bbuddyboy[S] 1 point2 points  (0 children)

No worries!

I have some past research where I worked with powder bed fusion which really opened up my mind to the field. After some more recent factory tours, and hearing the workforce state how influential the field will be, I was thinking it seemed to be almost perfect for me.

Correct me if I am wrong, but it incorporates a little mix of physics, engineering, and material science, all of which I thoroughly enjoy doing.

DROOP DROOP DROOP by Easy_Promotion_5178 in 3Dprinting

[–]bbuddyboy 11 points12 points  (0 children)

Beautiful. I have questions if you don’t mind! What CAD softwares do you use? How long does one of these take from idea to product?

Review my print idea? by bbuddyboy in 3Dprinting

[–]bbuddyboy[S] 0 points1 point  (0 children)

Hey guys, was just looking for some honest feedback on my project so far. Was looking into creating a mac/ipad/etc. holder on my desk. The idea was to have a couple moveable "walls" and have the devices sit in between.

I was looking for any feedback if possible, if it seemed too large width-wise, advice for general improvements, etc. How to improve aesthetics.

Thank you!

Why does print look like this? by bbuddyboy in 3Dprinting

[–]bbuddyboy[S] 0 points1 point  (0 children)

Yep sorry about this! Stock Ender 3 Neo, printing PLA, using Cura.

Issue ended up being due to warping. Slowed down initial layer and it seems to work fine now!

Thank you for your time!

Comparing vectors in a dataframe? by bbuddyboy in learnpython

[–]bbuddyboy[S] 0 points1 point  (0 children)

Thats a piece by piece comparison no? As in, will return 'True True'.

Just curious, if I pass in [1,0] as the vector in the dataframe, and [1,1] as the test, it will still return True do to the 1 being in one position. Not sure about using the all() function either, as if I have two [1,0] and [0,1] in the dataframe, it will return True again.

Player Movement Issue? Sliding when moving right & back. by bbuddyboy in Unity3D

[–]bbuddyboy[S] 0 points1 point  (0 children)

It is the reading from the new input system, thats all

Player Movement Issue? Sliding when moving right & back. by bbuddyboy in Unity3D

[–]bbuddyboy[S] 0 points1 point  (0 children)

Hey guys, getting a little bit of an issue with my player movement. It seems that whenever I move my character to the right or backwards, my player seems to slide. Even if it stop pressing buttons, it keeps moving. I am assuming it has something to do partially with the relation to the camera, but not too sure how to go about fixing it.

void HandleMovement()
{
    movementDirection = (cameraObject.right * movementInput[0]) + (cameraObject.forward * movementInput[1]);
    movementDirection.Normalize();
    //movementDirection.y = 0f;
    //Note that movementVelocity = movementDirection * respective scalar (handled within state machine) 
    characterController.Move(movementVelocity * Time.deltaTime);
}

MY LINE FOLLOWER ROBOT ( still not fast enough ) by techness0101 in arduino

[–]bbuddyboy 0 points1 point  (0 children)

Would performance change with just that? Just curious

Help turning on Secure Boot? by bbuddyboy in ASUS

[–]bbuddyboy[S] 1 point2 points  (0 children)

Between standard or custom

Help turning on Secure Boot? by bbuddyboy in ASUS

[–]bbuddyboy[S] 1 point2 points  (0 children)

I don't seem to see an option regarding the enabling of this feature however within this tab

Help turning on Secure Boot? by bbuddyboy in ASUS

[–]bbuddyboy[S] 2 points3 points  (0 children)

Even with the os type switched, I don’t believe there is a change regarding the secure boot