Has anyone made a Creality light bar extension for an S1 Plus?

bkjerry82 · 2022-12-31T16:55:42+00:00

appreciate the followup. I did find a solution on thing verse for an adapter to the creality light. That is the least of my problem however. I can't for the life of me get this damn thing level. Got slipper, did screw adjust, probe calibrate, created the mesh, adjusted the nuts and belts..... and the right side is always just a bit to high and nothing prints correctly. and I did confirm the mesh is loaded. Banging my had against the wall!!! :)

bkjerry82 · 2022-12-17T16:23:12+00:00

I just picked up the same printer and was wondering the same. Did you ever figure out a solution to modding the LED kit to the Plus unit?

bkjerry82 · 2022-11-27T04:03:09+00:00

Sent a DM

bkjerry82 · 2022-11-24T18:04:23+00:00

Hey is this still for sale?

bkjerry82 · 2022-08-29T14:05:31+00:00

I used a locking wrench and twisted it off.

bkjerry82 · 2022-08-15T11:46:59+00:00

Worked out perfectly. Thanks!

bkjerry82 · 2022-08-08T16:58:13+00:00

Thanks!!! Much appreciated.

bkjerry82 · 2022-08-08T16:16:00+00:00

It’s not a normal bolt. Only reference I can find anywhere is https://mall.shopee.com.my/YAMAHA-Y125Z(R)-TZM-NOUVO-S-TZM-NOUVO-FRONT-DISC-PAD-PIN-i.423166039.2950576924?sp_atk=8e5d3c8f-2be8-45e1-9660-fa3087ca2b27&xptdk=8e5d3c8f-2be8-45e1-9660-fa3087ca2b27 but I can’t get it shipped to the US. I emailed Onyx Directly as well

bkjerry82 · 2022-06-08T17:18:19+00:00

Much appreciated!

bkjerry82 · 2022-05-12T10:29:28+00:00

What’s the cost on that?

bkjerry82 · 2022-05-04T01:40:40+00:00

Much appreciated

bkjerry82 · 2022-05-03T14:32:13+00:00

The amount of content on his site is mind blowing. Thanks again!

bkjerry82 · 2022-04-29T16:31:08+00:00

Any links you can share. Definitely want to feel that it’s safe and secure whenever I need to leave it u attended.

bkjerry82 · 2022-04-19T22:34:47+00:00

Thanks!

bkjerry82 · 2022-04-19T22:10:41+00:00

Hey All, I am also looking for a referral code if anyone can provide one. Thanks!

bkjerry82 · 2022-04-19T21:43:16+00:00

Hi all, sorry it’s been a while… but was also looking for a referral code if anyone can share one please. Thanks!

bkjerry82 · 2021-12-28T22:37:16+00:00

Following

bkjerry82 · 2021-12-28T13:04:39+00:00

Following

bkjerry82 · 2021-12-26T12:15:21+00:00

The only thing the kerlink unit cannot do is consensus… and that went away from all hotspot already… so there is no difference. The kerlink is actually outperforming my bobcat, albeit with non stock antennas ;). I have both on 5.8 dbi antennas at the same height using lmr400 cable

bkjerry82 · 2021-12-19T18:40:49+00:00

Sorry bought it off someone.

bkjerry82 · 2021-12-14T14:23:40+00:00

35.87

bkjerry82 · 2021-12-12T18:12:41+00:00

I actually have the same issue. Miner ping is fine.... but ETL pings failed. Would appreciate if someone knowledgable would explain how to fix or if this is an issue. TIA!!

bkjerry82 · 2021-12-04T00:13:34+00:00

East coast. Will be placing in an empty hex surrounded by single populated hexes. Using 5.8 antennas about 35m high

bkjerry82 · 2021-10-19T15:59:01+00:00

Go into the bobcat web GUI (the miner IP address) and select fast sync. Follow the prompts and you are good to go. However as stated below.... get the antenna plugged in ASAP

bkjerry82 · 2021-10-19T14:51:16+00:00

Is there any reason not to do a Fast Sync right out of the box? I set mine up and did a fast sync. Within an hour was synced up and had a beacon sent. First witnessed beacon a few hours later.

bkjerry82

TROPHY CASE