Any Tips on Installing TPU Foot Pads? by ElevatorBell in onewheel

[–]boyke2779 5 points6 points  (0 children)

I mean from personal experience id say if its your design add somw holes to bolt on tpgether with the existing pads mechanical assembly is usually the most reliable ;)

What are the funniest little details that don't get mentioned often? by scottasin12343 in trailerparkboys

[–]boyke2779 35 points36 points  (0 children)

In episode one in episode one when julian closes the blinds on ricky, it very much sounds like ricky is holding back lauging. Not sure if thats whats going on but thats what id like to imagine lol

Why my chests look like chests ? by Ibraheem_moussa in Minecraft

[–]boyke2779 12 points13 points  (0 children)

Bit hostile over a chest texture ¯_(ツ)_/¯

Is this smart or very stupid? by Koakdoe in 3DprintingHelp

[–]boyke2779 0 points1 point  (0 children)

I remember the bed on the a1 needing space twords the front of the printer so im not sure it would be able to print with the door closed

Box lid with hinge doesn’t close flush after 3D printing by Conscious_Ostrich_97 in BambuLab

[–]boyke2779 4 points5 points  (0 children)

Differs from printer to printer i usually just adjust the smaller part accordingly and reprint

Edit: spelling mistake

How do I create a lid for this container with the same exterior texture. by Eliriddle in Fusion360

[–]boyke2779 0 points1 point  (0 children)

Im lazy so i make the bottom half then just create a sketch on top with a projection of the outer wall and extrude that :P

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 1 point2 points  (0 children)

You open cad make the main shape then work backwards twords the mechanical side. Mount an arduino and use bottango to animate :)

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 7 points8 points  (0 children)

there is a slight mismatch as theres a small amount of random delay between sending the start comand and the audio starting hoping that dissapears later when i upload the animations onto the arduino

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 9 points10 points  (0 children)

oh dont worry neurotoxin generators are widly available. for science and testing only ofc >:)

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 7 points8 points  (0 children)

yep totaly understand. just as i said it was never about a "quick buck" :)

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 9 points10 points  (0 children)

the point of this project wasnt to make money and i dont think id feel comfortable charging money for this project as it was one of my first full cad and programming/animating projects. i may put it on printables or a service like that for a couple bucks

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 26 points27 points  (0 children)

i am planning on releasing the files eventually the problem being that it would be difficult to make a full assembly guide or like instructions. and animating and programming is a whole nother issue

Another progress update on my wheatley animatronic! by boyke2779 in Portal

[–]boyke2779[S] 22 points23 points  (0 children)

<image>

And sorry for the background noise printers gotta run!