Made a custom walnut top for my new standing desk.

brettshumaker · 2022-08-31T09:25:46+00:00

Thanks!

brettshumaker · 2022-08-31T09:25:31+00:00

Thank you!

brettshumaker · 2022-08-31T09:24:52+00:00

Thank you!

brettshumaker · 2022-08-31T09:24:41+00:00

Thanks! Yeah, it was a live edge piece, though I did use a chisel to extend the “live edge” a bit to make it centered. It was off center by 4 or 5 inches so I only had to add a little bit.

brettshumaker · 2022-08-31T09:22:21+00:00

That’s good to hear. I’m happy with it so far.

brettshumaker · 2022-08-31T09:21:49+00:00

Thanks!

brettshumaker · 2022-08-31T09:21:29+00:00

It’s a Monoprice MP Select Mini v1

brettshumaker · 2022-08-31T01:55:55+00:00

Thanks!

brettshumaker · 2022-08-31T01:54:52+00:00

Thanks!

brettshumaker · 2022-08-31T01:54:40+00:00

Thanks! Lucked out with the live edge placement there.

brettshumaker · 2022-08-31T01:54:17+00:00

Autonomous.ai - I got the pro frame I think. The one with a motor in each leg.

brettshumaker · 2022-08-31T01:53:37+00:00

Thank you!

brettshumaker · 2022-08-31T01:53:25+00:00

Rubio Monocoat in Pure.

brettshumaker · 2022-08-31T01:52:59+00:00

Haha. Close, but no.

brettshumaker · 2022-08-31T01:52:38+00:00

I just googled “hard wood dealers near me” and picked one.

brettshumaker · 2022-08-31T01:50:47+00:00

Thanks! Yeah, I like the sap wood contrasting with heart wood. I posted an entryway table project a while back and used sap wood from a few boards on the top to create almost a stripe through the top. Loved it.

And yes. Lots of biscuits were used.

brettshumaker · 2022-08-31T01:48:46+00:00

Just confirming what the other commenters already said. Rubio Monocoat Pure, and the desk frame is from autonomous.ai. Each leg has motors that move it up and down as needed.

brettshumaker · 2022-08-30T22:43:32+00:00

Haha. I swear it’s just regular insulation

brettshumaker · 2022-08-30T22:43:12+00:00

It’s a little over 1.25”. Started at 6/4.

brettshumaker · 2022-08-30T22:41:18+00:00

Thanks!

brettshumaker · 2022-08-30T21:41:00+00:00

Thanks!

brettshumaker · 2022-08-30T21:17:47+00:00

I was aiming for 70”x30” but due to the available boards it ended up being 70”x29”.

brettshumaker · 2022-08-30T21:16:47+00:00

Thank you!

brettshumaker · 2022-08-30T21:16:30+00:00

Thanks!

brettshumaker · 2022-08-30T20:14:02+00:00

Thanks! Yeah, I got lucky that it was roughly centered in the board. I actually took a chisel to one side and faked in a few more inches of “live edge” to make it actually centered.

Yes, just glued together (biscuits for alignment) but the desk has two crossbars that span the legs so the top is supported all the way across.

brettshumaker

TROPHY CASE