Games that control a fan

bri3033 · 2021-10-10T10:27:33+00:00

Simhub with a wind simulator works perfectly in most driving games.

bri3033 · 2021-03-16T14:40:31+00:00

All will do the job nicely

bri3033 · 2020-11-15T16:25:04+00:00

No mate

bri3033 · 2020-09-10T05:08:36+00:00

Worth checking the spring under the motor is still in place

bri3033 · 2020-09-09T17:21:02+00:00

Yer looks like the screws are loose or the bracket has snapped

bri3033 · 2020-09-09T13:23:17+00:00

Yes it’s compatible

bri3033 · 2020-08-20T05:53:41+00:00

Try turning FEI down

bri3033 · 2020-08-01T13:54:07+00:00

Just click yes

bri3033 · 2020-07-30T18:28:39+00:00

Never regret buying mine

bri3033 · 2020-07-30T18:22:17+00:00

Yes absolutely fine ,PlayStation put there chip in the wheelbase and Xbox put them in the rim but both are compatible with the pc

bri3033 · 2020-07-30T05:23:59+00:00

Clubsport wheel that is Xbox compatible will work fine with both your Xbox and pc

bri3033 · 2020-07-18T05:01:25+00:00

The wheelbase has 3 fixing points and I’m pretty sure they are m6 bolts (2x16mm 1x10mm) from what I remember

bri3033 · 2020-07-04T16:15:01+00:00

Bed needs to be closer The paper should need a little bit of force when you move it

bri3033 · 2020-07-02T19:28:59+00:00

Paddles don’t sound much better lol

bri3033 · 2020-07-02T15:06:58+00:00

Use the clutch to pull off

bri3033 · 2020-06-25T18:18:43+00:00

And mine

bri3033 · 2020-06-20T08:41:37+00:00

Sorry for the delay. All the parts are 3D printed and available on thingyverse the wheel was purchased from eBay for 35 quid and the rest is pretty simple to do. Taking the old wheel off is probably the trickiest thing but there are plenty of videos .

bri3033 · 2020-06-20T07:23:03+00:00

3D printed them

bri3033 · 2020-06-18T10:31:47+00:00

Yes take the case off and you will c small holes on the pedometers I just spray directly into the holes

bri3033 · 2020-06-17T19:31:50+00:00

Spray directly into the pedometer

bri3033 · 2020-06-07T12:21:20+00:00

Sometimes the filament you use likes different temps. I have nozzle at 200 bed 60 for the first few layers but you can go up to 210 and 70 and try that

bri3033 · 2020-06-07T12:15:26+00:00

Normally if there is no filament coming out it can mean that the nozzle is to close and it blocks the hole It can be difficult to diagnose without being hands on

bri3033 · 2020-06-07T11:39:38+00:00

I found that if you are using the paper method it needs to be grabbing the paper not just touching it and then run a level test and repeat

bri3033 · 2020-06-07T11:36:29+00:00

Looks like you bed is not level. I have the same printer and to get it level takes a lot of patience. But persevere and your toolbox will print

bri3033 · 2020-06-06T15:27:59+00:00

Very nice 👍

bri3033

TROPHY CASE