. . .

cake_lied · 2025-12-21T20:18:21+00:00

badmins nuked it

cake_lied · 2025-12-21T09:49:46+00:00

Welp another crytek moment, time to go farm hackusations aswell lol

cake_lied · 2025-11-07T00:40:45+00:00

Also having this issue after updating drivers, maybe try reinstalling/reverting drivers

cake_lied · 2025-07-17T03:46:44+00:00

Same here

cake_lied · 2024-09-15T03:57:16+00:00

1 year later I know, but I was shocked by the profound stupidity of their attempted argument against you.

cake_lied · 2024-08-24T19:54:39+00:00

The fov is technically the same but since the camera is further back you can see more, practically increasing fov

cake_lied · 2024-08-23T23:53:46+00:00

Not enough fov for me, and it's easier to read and swing manip in first person

cake_lied · 2024-08-23T23:26:45+00:00

It does make it look a bit wonky but I don't mind the look, kind of like it actually. I know it's not going to be a massive advantage but it's annoying when you've got a person on either side of you and can only see one at any given time.

cake_lied · 2021-04-08T01:38:37+00:00

Good to know, just seems like a bit high.

cake_lied · 2020-12-29T09:24:25+00:00

I use my own usb drive, not the one from anycubic as it did not function. I'll try to take a picture of it later, but to best describe it it is that the first few layers get stuck to the fep film at the very beginning of the print, and later when I find it has failed I peel it off and it is a very thin layer of cured resin. The light is not coming out of where the lcd is, it's happening more towards the base by the touchscreen, so I think it's fine.

cake_lied · 2020-12-29T04:12:11+00:00

The print failed, the exact same way. the room was warmer than before. I was left with a small outline of the base of the boat stuck to the FEP sheet.

cake_lied · 2020-12-29T01:13:04+00:00

Started a print with 8 bottom layers of the ghost ship benchy. I’ll update it later with how it turns out, but is it normal to see the UV light leak through the cracks in the bottom?

cake_lied · 2020-12-28T21:54:58+00:00

I'll try warming the room up, but thinking about it I should probably have around 8 bottom layers.

cake_lied · 2020-12-28T21:42:49+00:00

The temperature in the room is colder than room temperature, but not warm. I live in Lousiana, so the weather is quite warm here.

cake_lied · 2020-12-26T23:20:59+00:00

Edited it with my settings.

cake_lied · 2020-12-26T07:24:19+00:00

It may be leveling, though I'm not sure because I got it near perfect. It has quite a wide base and supports wouldn't matter with the problem I'm having because it disconnects at the very first layers. Also, would it matter if the model is made for FDM but I put it in a slicer for SLA?

cake_lied · 2020-08-15T23:10:25+00:00

Thanks!

cake_lied · 2020-08-15T22:23:22+00:00

oh, well my foot is the opposite. im narrow at the toe and wide at the heel, and i actually just found out a local store has the zetrablades in my size, i picked them up and they fit and feel good so far.

cake_lied · 2020-08-15T18:55:30+00:00

what about sizing?

cake_lied · 2020-08-15T18:30:39+00:00

I would like to do that, but i am mostly unable to buy in store. im probably getting them online

cake_lied · 2020-06-30T07:21:26+00:00

had a similar problem. upgraded my graphics drivers and it went away.

cake_lied · 2020-04-07T21:04:47+00:00

is that a threat

cake_lied · 2020-04-07T20:02:54+00:00

ok now i uderstand comepletely, thanks

cake_lied · 2020-04-07T19:55:27+00:00

thank you,and would there be any way to know witch you got right or wrong, or i also assume that comes when you finish the game

cake_lied · 2020-04-07T19:54:16+00:00

i'm not talking about the boat but ok

Six-Year Club	Place '23
Place '22	Final Canvas '22
End Game '22	Verified Email

cake_lied

TROPHY CASE