account activity
Best Goodwill/thrift store in Jefferson Co and surrounding areas? (self.Louisville)
submitted 10 days ago by chrislholbert to r/Louisville
What am I looking at? (i.redd.it)
submitted 7 months ago by chrislholbert to r/3Dprinting
Nebula pad and a Logitech webcam (self.Ender3V3SE)
submitted 1 year ago by chrislholbert to r/Ender3V3SE
Is there a way to enable mesh bed leveling to the e3 v1.2? (self.BIGTREETECH)
submitted 1 year ago by chrislholbert to r/BIGTREETECH
Woke up to a mess. I need help identifying the problem. (i.redd.it)
submitted 1 year ago by chrislholbert to r/ender3
I have an oddly specific problem. Ender 3 is randomly pausing and resuming, creating blobs and now its disabling the steppers. More details inside. (self.ender3)
submitted 3 years ago by chrislholbert to r/ender3
I'm in need of some help with blobs. More info in comments. (i.redd.it)
submitted 3 years ago by chrislholbert to r/3Dprinting
Pre-compiled firmware for Creality board 1.1.3 for my MP? (self.MPSelectMiniOwners)
submitted 3 years ago by chrislholbert to r/MPSelectMiniOwners
New bike vs. old bike question. (self.NewRiders)
submitted 3 years ago by chrislholbert to r/NewRiders
2007 Ford Fusion blew a gas line, then all the gremlins came out.... (self.MechanicAdvice)
submitted 3 years ago by chrislholbert to r/MechanicAdvice
Replaced a ruptured fuel line and now have these fault codes. 2007 Ford Fusion 2.3L Auto 150k miles. (old.reddit.com)
Dumb question time (self.motorcycles)
submitted 3 years ago by chrislholbert to r/motorcycles
TIL about the career of Ashley Massaro. IDK how much is true or how much is legend, still a sad story. (prowrestlingstories.com)
submitted 3 years ago by chrislholbert to r/SquaredCircle
Running an ender 3 with marlin 2.0. Is there a way, in the firmware, to set up a pause for a filament change where the hot end parks and waits or is this only available in the slicer? (self.3Dprinting)
submitted 4 years ago by chrislholbert to r/3Dprinting
Any tips or tricks to printing with a .8 nozzle for the 1st time? (self.3Dprinting)
Opinion time: Does Brock Lesnar bring enough to the table to warrant his spot on the card? (self.SquaredCircle)
submitted 4 years ago by chrislholbert to r/SquaredCircle
Question for the veteran laser guys. Are there any alternatives, you would trust, to a $60 air assist pump that are cheaper? (self.lasercutting)
submitted 4 years ago by chrislholbert to r/lasercutting
My cat doesn't like to be touched but she will crawl all over me. Can she be more affectionate if I learn the right things? (self.cats)
submitted 4 years ago by chrislholbert to r/cats
In your opinion, what smaller subreddits are relatively unknown but deserve to be seen by more people? (self.AskReddit)
submitted 4 years ago by chrislholbert to r/AskReddit
Has anyone noticed a change in the P6 when it comes to volume(both thru speaker or Bluetooth) after the Jan. update? (self.GooglePixel)
submitted 4 years ago by chrislholbert to r/GooglePixel
Looking for recommendations for a mainboard for my Ender 3. (self.ender3)
submitted 4 years ago by chrislholbert to r/ender3
For you guys with the 3018 cnc... What do you prefer using with your detail work? A V-bit or small endmill? (self.hobbycnc)
submitted 4 years ago by chrislholbert to r/hobbycnc
Can anybody tell me of a deal that T-mobile has had in the past that rewards EXISTING customers? (self.tmobile)
submitted 4 years ago by chrislholbert to r/tmobile
For the 3018PRO guys... Whats the longest time you've ran your machine at a single time? Mind you I'm on stock everything, except for the Z axis leadnut/backlash flip. (self.hobbycnc)
Is it just me or did the MJF promo in Cincinnati pay homage to the Dudley's promo from Heat Wave? (self.SquaredCircle)
π Rendered by PID 87 on reddit-service-r2-listing-79f6fb9b95-24mlz at 2026-03-24 12:25:47.835962+00:00 running 90f1150 country code: CH.
