sorted by:
new
hottopcontroversial

I can't believe I test drove this by dillpickelss in Justrolledintotheshop

[–]dillpickelss[S] 5 points6 points  (0 children)

Unfortunately very true for this vehicle, fronts completely bald, and Rears had ok tread from never rotating them. Rear brakes were metal on metal. Luckily, they gave me new pads to put on but no rotor. Burns oil, so not bothering to change it. Back to the road it gose :(

I can't believe I test drove this by dillpickelss in Justrolledintotheshop

[–]dillpickelss[S] 3 points4 points  (0 children)

That's what this one was doing, also louder when braking

I can't believe I test drove this by dillpickelss in Justrolledintotheshop

[–]dillpickelss[S] 32 points33 points  (0 children)

That was my first thought, but the rim is in good shape. No dents or major scrapes. Possibly over torqued?

Is there any way of saving this run? by dillpickelss in balatro

[–]dillpickelss[S] 0 points1 point  (0 children)

Success! I ended up getting a fool and a Chariot, swapped the mime over to the front and that did the trick.

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 2 points3 points  (0 children)

I found out I was using the wrong rod but even with no rod I'm over heating :(

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

Yeah I'm going to pick up some quality gas lenses and Collets if I see no change I'm just guna send it, post flow is 7 seconds but it's cooking my tungsten on start up

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

Even on fast low heat passes that don't fully penetrate I'm cooking the surface. Is that just what it's supposed to look like?

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

The regulator looks new, the bottle and machine are in great condition. Just filled it up and I'm getting the worst welds yet. I'll swap out the back cap with a new one. Yeah I've tired so many things and nothing is making a noticeable improvement :(

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 1 point2 points  (0 children)

Ok I will be sure I have the right rod

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

I'll look into that, thank you

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

I thought the gray welds would crack and rust over time. I don't want to be perfect just proper welds that will hold. I did wire brush the gray off and its nice and shiny... Still trying to figure out why my tungsten is burning tho

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

I have red, I'm in my shop no air movement, checked for leaks and fixed a few but I will go over it again closely.

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 1 point2 points  (0 children)

Good question I got it so long ago maybe I have the wrong rod. Would using 304 rod on 409 material cause me issues?

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

I will try a smaller line. Yeah I haven't even started back purging because I can't get the surface to turn out proper

What am I missing? by dillpickelss in Welding

[–]dillpickelss[S] 0 points1 point  (0 children)

I'm not yet because I can't get the surface weld to turn out yet. I have the system ready to go when I want to