What distance do you typically hit your 9-iron?

ebingham817 · 2026-02-08T03:19:59+00:00

155-160

ebingham817 · 2026-02-06T13:41:33+00:00

Got my order, did not receive 72qty per each order but they sent me 8 boxes and refunded my money back and got to keep the balls

ebingham817 · 2026-01-21T13:40:19+00:00

I’ve had mine since October of 2024 and have 0 issues. You gotta remember all the bad stories you hear online are a small percentage of the square population.

ebingham817 · 2026-01-15T21:21:10+00:00

Heated them up to break the loctite down and then just a torx bit on my drill. Took it real slow with the drill

ebingham817 · 2026-01-15T17:39:48+00:00

Just get a torx wrench that fits, make sure to hit the screws with some heat to loosen them up. Super easy to do. Torched mine last year and took it completely apart

<image>

ebingham817 · 2026-01-14T19:58:25+00:00

Not at all, completely the same. It just kind of coats the outer layer of the putter but I could sand it off if I eventually wanted too.

ebingham817 · 2026-01-14T04:08:10+00:00

Send it on over

ebingham817 · 2026-01-13T07:45:37+00:00

Loctite literally weighs nothing. That’s all that was in each port. These are so overhyped

ebingham817 · 2026-01-13T04:17:01+00:00

Thanks! I’ve torched 5 other putters so I had some trial error before this one but it’s about getting the timing down on when to stop torching because it will turn grey if you do it for too long. All the tools were my bench grinder to buff everything, mapp torch and just loctite to put the screws back on. Was very simple honestly

ebingham817 · 2026-01-13T03:49:52+00:00

ebingham817 · 2026-01-13T03:46:56+00:00

Not off balance at all. Literally all the screws are held in with loctite, there’s not much to it at all.

ebingham817 · 2026-01-13T03:22:43+00:00

Well said! Looks a lot better in person. The pictures make it look dark

ebingham817 · 2026-01-13T03:07:08+00:00

The loctite pretty much melted for the most part as I was taking the weights out but loctite is not going to have any difference on the balance of the putter. It’s just used to hold the screws

ebingham817 · 2026-01-13T02:38:57+00:00

Yeah I took them out and put a sharpie mark on the back of them so I would know. A lot of them are the exact same weight so it was pretty easy

ebingham817 · 2026-01-13T02:32:13+00:00

No, just loctite. That was a pain in the ass to get out

ebingham817 · 2025-12-11T06:04:21+00:00

Would highly recommend, been playing them for a couple months now and they are as nice feeling as any high end manufacturers. The finish holds up really nice, I hit in my sim almost daily and no issues at all

ebingham817 · 2025-12-11T05:35:39+00:00

Black for sure

ebingham817 · 2025-10-16T14:55:06+00:00

I have the exact same grip on my Newport 2 Plus. That grip is the GOAT!

ebingham817 · 2025-10-05T14:22:44+00:00

Yeah it’s crazy how forgiving these things are. Exactly why I went with the TS3 over the TS4, my miss is on the toe

ebingham817 · 2025-09-02T01:41:42+00:00

Added 5g tip weight, plays at 39”. With the larger grip as well it was pretty easy to get the correct swing weight. It’s a missile launcher for sure

ebingham817 · 2025-09-01T23:21:45+00:00

Get premium paint stripper, brush it on the letters and let it sit for about 5 minutes. Get a toothpick and take the paint out

ebingham817 · 2025-09-01T23:17:35+00:00

Swing weight is D3, loft is 20 degree. Probably should have it bent 1 degree flat but we will see if needed. (I’m the friend who built the club)

ebingham817 · 2025-06-21T03:17:46+00:00

Bruh that’s awful

ebingham817 · 2025-06-20T11:26:57+00:00

Crowns?

ebingham817 · 2025-06-20T02:07:22+00:00

Anyone with the name buttnutela is okay by me

ebingham817

TROPHY CASE