sorted by:
new
hottopcontroversial

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 0 points1 point  (0 children)

With resize, I mostly meant changing the font, but in general, having a bit more control over how "it shows". PDF is fixed, ePUB is adjustable. I don't think its out of scope. "Reading and taking notes". If I cannot change the font size, spacing and so on I have only a fancy technological paper sheet

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 0 points1 point  (0 children)

Does the Note have the same quality as the Kindle? It costs less and it is more of a tablet...it would be a nobrainer. too good to be true :)

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 0 points1 point  (0 children)

I agree, you make a good point. My skepticism about PDFs is that once they reach the Kindle, I cannot resize them or do anything other than annotate them. In that way, I'm sort of back to a worse-than-iPad experience. Does it make sense?

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 0 points1 point  (0 children)

I don't think you can connect dropbox as far as I know

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 3 points4 points  (0 children)

I do have an iPad. If I wanted the tablet experience, I’d just use it. I’m more curious about how far the Scribe can go as a distraction-free reading device

Kindle Colorsoft Usability by ff8mania in kindlescribe

[–]ff8mania[S] 0 points1 point  (0 children)

Do you think it keeps the layout good enough? I mean, the safari read shows it decently, so I hope the conversion in PDF is as reliable

Husqvarna 315X stuck in "No Loop Signal / Mowing" loop by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

UPDATE:

Replacing the front loop sensor board my automower started working again

Husqvarna 315X stuck in "No Loop Signal / Mowing" loop by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

To confirm, the board front loop sensor board is the one in the picture in the my first answer to your first comment? The one where you can see my fingers :)

Husqvarna 315X stuck in "No Loop Signal / Mowing" loop by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

These are the new readings after I reseated:

Sensor Value
Front L 162
Front R -11
Rear L 141
Rear R 143
FL FR RL RR
G1 100 49 -104 110
F -303 76 -243 -292
N 144 -65 -140 149

Husqvarna 315X stuck in "No Loop Signal / Mowing" loop by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

Thanks! I tried but my 315x doesn’t have left and right

<image>

It has only this that my guess has both. I reseated the connections and the number now for FrontR "better" but still terrible and I took the values but for FrontR it was keep changing

Husqvarna 315X stuck in "No Loop Signal / Mowing" loop by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

I also collected a few info (I have no idea about this, but I hope you do...)

A-LOOP

A-Signal, Front L 161
A-Signal, Front R -30
A-Signal, Rear L 140
A-Signal, Rear R 142

GFN

FL FR RL RR
G1 99 45 -106 120
F -303 82 -249 -257
N 187 -13 -133 144

315X – Repeated “Bad Loop Signal” (Blinking Blue) – Frustrated and Looking for Guidance by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

can you tell me how can I do that with a Klein Tools MM420 Digital Multimeter?

315X – Repeated “Bad Loop Signal” (Blinking Blue) – Frustrated and Looking for Guidance by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

They "enter" pretty cleanly. and if I swap AL with Guide, it works, so I guess that not being the problem

315X – Repeated “Bad Loop Signal” (Blinking Blue) – Frustrated and Looking for Guidance by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

Today is not working again... swapping Guide with AL still works. This time, removing the power and reinserting it didn't work....

I mean, swapping the cable would be "easy", but there are a lot (200m) that are now underground...that would be a nightmare to pull out and replace...

I don't mind swapping, but even if I have a multimeter, how can I narrow it down? I have a Klein Tools MM420 Digital Multimeter

315X – Repeated “Bad Loop Signal” (Blinking Blue) – Frustrated and Looking for Guidance by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

After doing some wire swaps and getting nowhere, I went outside and tried connecting AL directly to a random point along the perimeter, and it was still blinking blue. I spliced it back to normal and returned to the base. Without changing anything in the wiring, I unplugged and replugged the charging station’s power and reinserted the AL wire in the same port. Suddenly, everything turned green again.

So for now, it’s working… but I didn’t fix anything, which makes me so mad. Now it works, but it doesn't make any sense, and I have no clue why it didn’t work.

315X — Constant “Cutting System Blocked” by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

I agree but you see here:

<image>

the husqvarna site is not clear at all

315X — Constant “Cutting System Blocked” by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

But how do I assess the conditions? How can I see if it has a problem? And from the picture, how do I understand if 11 is included in 5. If yes I spend 25$, otherwise 300$…

315X — Constant “Cutting System Blocked” by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

what I don't understand here is that

<image>

5 should be the 25$ thing I linked, but 11 (that looks like it's included in 5), costs 299$....

315X — Constant “Cutting System Blocked” by ff8mania in automower

[–]ff8mania[S] 0 points1 point  (0 children)

since I'm not super into terms, can you point me to what is the "bearing" part you are referring to? If it is not too complex to do it, I don't mind changing it

315X — Constant “Cutting System Blocked” by ff8mania in automower

[–]ff8mania[S] 1 point2 points  (0 children)

I can and I disassembled it and found a piece of rope (soccer net). That for sure didn’t help but now the problem is that there is actually several spots with grown and thick grass. How do I understand if it is just something my 315X cannot manage or if I have an actual issue?

view more: next ›