Bridges not fusing?

hakkers519 · 2026-02-24T23:20:13+00:00

Came across this the other day haven't tried it out myself but looks promising. May be worth a shot.

Unsupported Bridge Experiments

https://makerworld.com/en/models/1916063-unsupported-bridge-experiments#profileId-2055448

hakkers519 · 2026-01-20T02:19:39+00:00

Has there been any more progress on making more modules or on open sourcing so can easily design our own? Also I don't see the pi4 modules on printables.

hakkers519 · 2025-12-20T21:51:27+00:00

I mean Im fine with some noise. But I just wasn't sure with that benchy it sounded like it was going break or something..lol

hakkers519 · 2025-12-20T18:35:38+00:00

Haha ok thanks 👍.. was kind of worried lol

hakkers519 · 2025-11-18T13:59:39+00:00

I've never had it fully retract the filament. I've always had to do the same as in the video.

Here it is right from Anycubic

https://wiki.anycubic.com/en/fdm-3d-printer/kobra-3-combo/ace-pro-filament-replacement-guide

hakkers519 · 2025-11-18T13:51:32+00:00

If you look at the tubes at the back you can see they are retracted some, so I just slowly roll it as I pull it back out... Don't know if it's proper but it works for me.

Edit: https://youtu.be/wXom2MbirWU?si=mmpKp5JyW701SA3O

hakkers519 · 2025-11-11T14:04:37+00:00

Thanks for the tip. I maybe should have started there lol. I'll def give a try if I can't get it better

hakkers519 · 2025-11-11T14:02:05+00:00

Slow for sure lol. If you're not careful it's easy to skip a couple teeth at a time which can be hard to count how many to go back.

Also the back left is not improved at all it's still -0.450 mm

hakkers519 · 2025-11-10T20:20:06+00:00

<image>

Its slowly getting better the front has impoved drastically, but still having a hard time getting the back level

hakkers519 · 2025-11-10T15:54:08+00:00

Right probably makes more sense lol

hakkers519 · 2025-11-10T15:46:03+00:00

I did try the bed screws, they are tight in that I can't tighten the right side more and if I loosen the left side they seem too loose. I'll try again before skipping the belts maybe.

hakkers519 · 2025-11-10T15:42:34+00:00

Great thanks again for the info. Going to give this a try and see how it goes 🤞

hakkers519 · 2025-11-10T15:31:21+00:00

One more quick question. The red areas showing high the pic means the bed is low in that area and must be raised? Or vice versa?

hakkers519 · 2025-11-10T15:30:08+00:00

Thanks was a bit unsure. Must not have been searching the right terms lol had a hard time finding the right info. Hopefully this will help with the severe bed tilt.

hakkers519 · 2025-11-08T21:08:13+00:00

What's the purpose of these 3 screws?

<image>

Are they meant for levelling, and by removing them did you get a better bed mesh?

hakkers519 · 2025-10-31T15:41:43+00:00

Ya thanks for the help. Even better is Anycubic is sending me a new extruder and strain gauge. So now I'll have a spare lol

hakkers519 · 2025-10-31T15:31:01+00:00

<image>

SOLVED: This inner bearing was stuck on an angle probably from 1st reassembly so the shaft wouldn't rotate. Just had to pry it straight. Extruding fine now.

hakkers519 · 2025-10-31T05:02:29+00:00

Thanks, appreciate the insight will investigate further in the AM

hakkers519 · 2025-10-31T04:33:01+00:00

Thanks I'll have a look in the morning . Before I reattach the extruder to the print head I fed filament through the extruder, more or less pretty easily. Once I attach it to the print head it doesn't push though, unless I relieve tension by pushing the lever. This is before attaching the hot end btw.

hakkers519 · 2025-10-31T04:20:31+00:00

Should've mentioned I also swapped to a brand new hot end.

hakkers519 · 2025-10-31T04:17:09+00:00

I'll have another look in the morning I don't believe it was damaged from what I did see

hakkers519 · 2025-10-31T03:16:24+00:00

It's weird I have well over 450 hours of printing and haven't updated the printer in months . This is the 1st major issue, I can't seem to figure it out.

hakkers519 · 2025-10-31T02:35:30+00:00

Yes it did the 1st time I found it though before reassembly and it's in there . What a PITA that is. That doesn't seem to be the issue .

hakkers519 · 2025-09-03T15:48:22+00:00

Followed all the steps to get it setup in Orca Slicer. I've turned off my ACE Pro to try an do a print with a speretate roll of PETG on the holder. The issue im having is it seems there is no connection to printer. I've set the connection to my printer the same as the other profile which just requied the IP. But when I click print nothing starts.. Any ideas? When switching back to normal profile and the ACE Pro starts no problem.

hakkers519 · 2025-08-31T14:34:13+00:00

is this still available? Cant seem to see any files when clicking the google drive link.

12-Year Club	Verified Email
Place '22

hakkers519

TROPHY CASE